Abstract:An alloy with a nominal composition of 70Mn–24.95Cu–3Al–2Zn–0.05Ce (at%) was prepared using vacuum induction melting (VIM) technology, or followed by directional solidification (DS) processing at withdrawal rates of 20 and 100 µm/s. Further, VIM, DS20 and DS100 alloys were aged at 703 K for 2 h. The microstructure, fcc-fct transformation and damping capacity of VIM and DS alloys have been investigated comparatively. The results show that the microstructure of VIM alloy mainly comprises equiaxial γ-MnCu dendrites while that of DS20 and DS100 ones is primarily composed of columnar γ-MnCu dendrites, and the directional effect of such columnar dendrite is obviously strengthened with increase in withdrawal rate. Two and three compositional segregations are present in VIM and DS alloys respectively, and fine α-Mn phase is formed in DS100 one. The starting fcc-fct transformation temperature of the alloy bears a relationship of TtVIM > TtDS20 > TtDS100. The stepped fcc-fct transformations occur and couple to promote the formation of phase transformation damping step due to compositional segregation, which is more obvious in DS alloys than in VIM one. The twin relaxation peak damping capacity of VIM and DS20 alloys is similar but evidently higher than that of DS100 one. The damping capacity of long columnar dendrite especially at 100 µm/s is also degraded due to strong grain boundary blocking effect. There exists a relationship of Q−1VIM > Q−1DS20 > Q−1DS100 for damping capacity of VIM, DS20 and DS100 alloys at room temperature over the whole strain amplitude range.

A Comparative Study on Microstructure and Damping Capacity of Mn-Cu Based Alloys with Dendrite and Equiaxial Grain

The Role of Dendritic Morphology and Segregation in fcc-fct Transformation and Damping Capacity of Mn–Cu Based Alloys

Microstructure and Properties of Mn-Cu-Based Damping Alloys Prepared by Ball Milling and Hot-Press Sintering

Microstructure and damping property of Mn-Cu damping alloy by induction brazing and different heat treating

Preparation and research on the structure and properties of high damping Mn-Cu alloy

Effect of Alloying Elements on Microstructure, Mechanical and Damping Properties of Cr-Mn-Fe-V-Cu High-Entropy Alloys

Effect of dendritic segregation on the damping property of MnCu alloy

Effect of Heat Treatment on Microstructure and Damping Capacity of Mn-Cu Alloy

Microstructure Evolution, Damping Capacities and Mechanical Properties of Novel Mg-xAl-0.5Ce (wt%) Damping Alloys

Effect of Mn Content on Microstructure and Damping Capacity of Fe-Mn Alloy

A Comparative Study on Microstructures of a High-Zn Alznmgcuzr Alloy Fabricated by Casting and Melt Spinning

Effects of Cu on Microstructure, Mechanical Properties and Damping Capacity of High Damping Mg–1%Mn Based Alloy

Designing Damping Capacity in High Strength Fe–Mn Based Alloys by Controlling Crystal Defect Configurations

A study of the ultrahigh damping capacities in Mg-Mn alloys

Study On The Damping Mechanism Of Fe-Mnn Alloy

High Damping Capacities of Mg-Cu Based Alloys

Effect of Pre‐Deformation and Subsequent Aging on the Damping Capacity of Mn‐20 at.%Cu‐5 at.%Ni‐2 at.%Fe alloy

Synergistic effects of a novel Cu51Hf14 inoculant and Zr element on the microstructure and properties of Cu-Al-Mn shape memory alloy

A Transmission Electron Microscopy Investigation of Defects in an Mg-Cu-Mn-Zn-Y Damping Alloy

Peculiar Microstructure with High Damping Capacity for Al0.5CrFe2Ni Medium-Entropy Alloy

Novel Cast-Aged MnCuNiFeZnAl Alloy with Good Damping Capacity and High Usage Temperature Toward Engineering Application