Abstract:Due to the high damping capacity and excellent mechanical properties, Fe-Mn alloy is considered to be a promising high damping alloy, and suitable for constructional and vehicle metal parts application, which can enhance the fatigue property of structures and metal parts, and also improve the working and living environment. It's generally accepted at present that damping capacity of Fe-Mn alloy is influenced by the stacking fault boundaries in gamma-austenite and epsilon-martensite, gamma/epsilon phase boundaries and epsilon/epsilon variant boundaries; another view is that boundaries of the above damping sources are made up of partial dislocations, so the damping capacity of Fe-Mn alloy is caused by the motion of partial dislocations, and interpreted by G-L dislocation pinning model and stacking fault probabilities calculation. But there is no distinction between the probabilities of different type stacking faults. Both deformation stacking fault and growth stacking fault can be formed in gamma-austenite and epsilon-martensite, and the change of process parameters has different influence on them, which will lead to different changes of deformation and growth stacking fault probabilities. So it's necessary to analyze whether boundaries of different stacking fault types will have different effects on damping capacity of Fe-Mn alloy. Based on that, a hot-rolled Fe-19Mn alloy is prepared and then solution treated between 950 similar to 1100 degrees C. Damping capacity is measured by dynamic mechanical analyzer (DMA). The microstructure evolution is observed by OM and TEM, and XRD is used to analyze phase constitution and to measure stacking fault probabilities. The results reveal that Fe-19Mn alloy shows amplitude-dependent damping capacity which almost linearly increases with amplitude, and frequency-independent damping capacity. From G-L plot, the variation of damping capacity below the critical amplitude A' (A'approximate to 30 mu m) is interpreted by G-L model, while it's associated with micro-plastic deformation when above A'. As the increase of solution treatment temperature, the damping capacity of Fe-19Mn decreases, and possesses the best performance at 950 degrees C; furthermore, it shows different characteristics in different amplitude ranges: when the amplitude is lower than 170 mu m, damping capacity decreases in exponential form, which changes similarily with deformation stacking fault probability in epsilon-martensite, so it can be considered the boundaries of deformation stacking fault as the main damping source; when the amplitude is higher than 170 mu m, damping capacity decreases linearly, which changes similarily with the relative length of gamma/epsilon phase boundary, so it can be considered gamma/epsilon phase boundary as the main damping source. Based on TEM observation of stacking faults in gamma-austenite, it can be inferred that stacking fault boundaries in gamma-austenite have no obvious contribution to the change of damping capacity of Fe-19Mn with amplitude.

The Role of Dendritic Morphology and Segregation in fcc-fct Transformation and Damping Capacity of Mn–Cu Based Alloys

Observation of Dendrite Growth Velocity and Microstructure Transition in Highly Undercooled Single Phase Alloys

A Transmission Electron Microscopy Investigation of Defects in an Mg-Cu-Mn-Zn-Y Damping Alloy

Damping characterization and its underlying mechanisms in CNTs/AZ91D composite processed by cyclic extrusion and compression

Effect of Cu/Mg-containing intermetallics on the mechanical properties of the as-cast HVDC AlSiMgMnCu alloys by SBFSEM at nano-scale

Effect of Ni alloying on vacancy behavior and damping capacity in martensitic ductile Cu–Al–Mn alloys

Influence of Solution Temperature on Á Transformation and Damping Capacity of Fe-19Mn Alloy

Microstructure and damping property of Mn-Cu damping alloy by induction brazing and different heat treating

High damping capacity of a Ni-Cu-Mn-Ga alloy in wide ambient-temperature range

Damping performance of SiC nanoparticles reinforced magnesium matrix composites processed by cyclic extrusion and compression

Simultaneous improvement of strength and damping capacity of Mg-Mn alloy by tailoring bimodal grain structure

Effect of Cu and Mn content on solidification microstructure, T-phase formation and mechanical property of Al Cu Mn alloys

Contribution Made by Double-Sized TiC Particles Addition to the Ductility–strength Synergy in Wire and Arc Additively Manufactured Al–Cu Alloys

Synergistic effects of a novel Cu51Hf14 inoculant and Zr element on the microstructure and properties of Cu-Al-Mn shape memory alloy

Microstructure evolution, Cu segregation and tensile properties of CoCrFeNiCu high entropy alloy during directional solidification

Evolution behavior of γ-D03 phase in Cu-15Ni-8Sn alloy and the corresponding effects on alloy property

Microstructures, Tensile Properties and Serrated Flow of AlxCrMnFeCoNi High Entropy Alloys

The mechanical and functional behaviors of Mn–15 wt.%Cu alloy produced by selective laser melting

Damping capacity and mechanical properties of Fe3Cr2NiCuAl medium entropy alloys by tuning phase constituents

Simulation of Dendritic Deformation Induced by Convection in Alloy Solidification

Simulation of the Dendrite Morphology and Microsegregation in Solidification of Al–Cu–Mg Aluminum Alloys