Abstract:The re-distribution layer (RDL) has been widely used in various high-performance applications because it greatly increases package density by rearranging the I/O terminals of the chip to an area with available space. However, the increase in current density and frequency in the Cu trace layer generates a large amount of Joule heat, especially in high power scenarios, which causes internal stresses in the RDL due to the mismatch of coefficients of thermal expansion (CTE) of different materials in the RDL, leading to reliability issues such as interface delamination between Cu trace and polyimide (i.e., Cu/PI interface), wafer warpage and so on. Aiming at providing guidance for the structural optimization of the Cu RDL in high-power applications, this study performs 3D finite element simulations to characterize the thermomechanical behavior of conventional Cu RDLs in fan-out wafer-level packages at different currents and Cu trace thicknesses, so as to predict potential failure sites and modes. A novel Ni-plated RDL is also used to comparatively investigate the effects of the ratio of Cu to Ni and the total thickness of the metal trace layer on the thermomechanical behavior of the Cu-Ni RDL. The results show that both Cu and Cu-Ni RDLs exhibit current crowding and stress concentration at straight trace sections and pad corners, with the maximum stresses appearing at pad edges. The interfaces between the metal trace, under bump metallization (UBM), and solder balls are critical for RDL reliability. For Cu RDL, increasing the thickness of the Cu trace can reduce current density and temperature, but result in an increase in maximum stress. So, a suitable Cu thickness needs to be selected for high-power applications. Besides, the raise of Ni content leads to the increase of the maximum stress and maximum current density in Cu traces, while the maximum temperature depends on its thickness. However, due to the superior adhesion of Ni to PI, its effect on interfacial reliability needs to be further investigated.

Optimization of Passivation and Top Metal Layer Crack in Temperature Cycle Test of RF-LDMOS

Study on Electro-Thermo-Mechanical Responses of Bonding Wires Arrays Used for the Package Design of Ldmosfet-Based Rf Amplifier

Product Design Optimization for Prevent Bias Highly Accelerated Stress Failure of RF-LDMOS

Improvement in Cavity and Model Designs of LDMOS Power Amplifier for Suppressing Metallic Shielding Cover Effects

Failure Mechanism Study for Flip Chip QFN Crack Issue under Temperature Cycling Test

Temperature Cycling Failure Analysis and Improvement of A Panel Level Fan-out QFN Package

Structural integrity optimization of 3D TSV package by analyzing crack behavior at TSV and BEOL

Fractures of Low-K Materials in a RF Package with Integrated Passive Device Based on TGV

Investigation on memory package crack and prevention under temperature cycling test

Optimization of Laser Cladding Forming Parameters by Numerical Simulation to Minimize the Cracking Posibilitys

Stress Analysis and Layout Optimization of Nano-TSV in an Advanced Packaging

Optimization of RF Performance and Reliability of 28V RF-LDMOS

Modeling and Simulation-Based Layout Optimization for Tolerance to TID Effect on n-MOSFET

A Combined Simulation and Experimental Study on Cracking and Delamination Behavior at the Cu/Polyimide Interface of RDLs in Chiplet Package Subjected to Thermo-Mechanical Loads

Effects of rheology of compound materials on passivation cracking of micro-structure of IC packages

Numerical Simulation of Reliability of 2.5D/3D Package Interconnect Structure under Temperature Cyclic Load

Optimization of Wet strip after Metal Hard Mask All-in-One Etch for metal void reduction and yield improvement

Fabrication of CaSiO 3 LTCC high aspect ratio microstructure by laser chemical assisted micro-milling

Improvement of Thermo-Mechanical Reliability of Wafer-Level Chip Scale Packaging

Thermomechanical Behavior and Reliability of Redistribution Layers with Ni-plated Cu Traces for High Power Applications

Reliability Simulation Analysis of TSV Structure in Silicon Interposer under Temperature Cycling