Abstract:The transients formed during the reactions of oxidizing radicals with 1-naphthol (1) and 2-naphthol (2) in aqueous medium have been investigated by pulse radiolysis with detection by absorption spectroscopy and density functional theory (DFT) calculations. The transient spectra formed on hydroxyl radical ((•)OH) reactions of 1 and 2 exhibited λ(max) at 340 and 350 nm at neutral pH. The rate constants of the (•)OH reactions of 1 (2) were determined from build-up kinetics at λ(max) of the transients as (9.63 ± 0.04) × 10(9) M(-1) s(-1) ((7.31 ± 0.11) × 10(9) M(-1) s(-1)). DFT calculations using the B3LYP/6-31+G(d,p) method have been performed to locate favorable reaction sites in both 1 and 2 and identification of the pertinent transients responsible for experimental results. Calculations demonstrated that (•)OH additions can occur mostly at C1 and C4 positions of 1, and at C1 and C8 positions of 2. Among several isomeric (•)OH adducts possible, the C1 adduct was found to be energetically most stable both in 1 and 2. Time-dependent density functional theory (TDDFT) calculations in the solution phase has shown that the experimental spectrum of 1 was mainly attributed by 1a4 (kinetically driven (•)OH-adduct) formed via the addition of (•)OH at the C4 position which was 0.73 kcal/mol endergonic compared to 1a1 (thermodynamic (•)OH adduct), whereas 2a1 (thermodynamic/kinetic (•)OH-adduct) was mainly responsible for the experimental spectrum of 2. Naphthoxyl radicals of 1 and 2 have been predicted as the transient formed in the reaction of (•)OH at basic pH. In addition, the same transient species resulted from the reactions of oxide radical ion (O(•-)) at pH ≈ 13 and azide radical (N3(•)) at pH 7 with 1 and 2. Further, UV photolysis of aqueous solutions of 1 and 2 containing H2O2 (UV/H2O2) were used for the (•)OH induced oxidation product formations up on 60% degradations of 1 and 2; profiling of the oxidation products were performed by using an ultraperformance liquid chromatography quadrupole time-of-flight mass spectrometry (UPLC-Q-TOF-MS) method. According to the UPLC-Q-TOF-MS analyses, the preliminary oxidation products are limited to dihydroxy naphthalenes and naphthoquinones with N2-saturation, while some additional products (mainly isomeric monohydroxy-naphthoquinones) have been observed in the degradations of 1 and 2 in the presence of O2. We postulate that dihydroxy naphthalenes are derived explicitly from the most favorable (•)OH-adducts speculated (preference is in terms of the kinetic/thermodynamic dominancy of transients) by using theoretical calculations which in turn substantiate the proposed reaction mechanisms. The observations of (•)OH-adducts for an aromatic phenol (herein for both 1 and 2 at pH 7) rather than phenoxyl type radical in the pulse radiolysis experiments is a distinct and unique illustration. The present study provides a meaningful basis for the early stages associated with the (•)OH initiated advanced oxidation processes of 1- and 2-naphthols.

Effect of Aramid Fiber Surface State on Properties of Epoxy Resin Composites

Effect of Irradiation Grafting Epoxy on Surface Characteristics of Carbon Fibers and Mechanical Properties of Composites

Preparation of highly active aramid fiber and effect on the interface property of aramid/epoxy composites

Surface Characteristics of Different Cross-Section Carbon Fibers and Its Effect on Interfacial Adhesion Properties of Composite

Effects of aramid nanofibers on the mechanical properties of epoxy resin and improved adhesion with aramid fiber

Characterization of fiber/matrix interfacial bonding strength of chemically grafted aramid fiber surface with epoxy resin composites

Enhancement of Para-Aramid Fibers by Depositing Poly-P-paraphenylene Terephthalamide Oligomer Modified Multi-Walled Carbon Nanotubes

Surface-modified alumina nanoparticles-filled aramid fiber-reinforced epoxy nanocomposites: preparation and mechanical properties

Improved dielectric and mechanical properties of aramid fiber reinforced epoxy resin composites by polyethyleneimine grafting

Latent active unit triggered crosslinking inside aramid fiber with improved transverse connection and composite properties

Surface Ammonification Of The Mutual-Irradiated Aramid Fibers In 1,4-Dichlorobutane For Improving Interfacial Properties With Epoxy Resin

Effect of fiber surface treatment with silane coupling agents and carbon nanotubes on mechanical properties of carbon fiber reinforced polyamide 6 composites

Mechanical Investigation of Epoxy Based High-Strength Carbon Fiber Braided Composites Modified with Silane Coupling Agents

Improvement of the Mechanical Properties by Surface Modification of ZnCl2 and Polydopamine in Aramid Fiber Composites

Influence of Polyamide Acid Coating Reaction on the Properties of Aramid Fibre

Surface modification of Kevlar fibre fabric and its influence on the properties of Kevlar/epoxy composites

Oxidation reactions of 1- and 2-naphthols: an experimental and theoretical study.

Effect of Coir Fiber Surface Treatment on Interfacial Properties of Reinforced Epoxy Resin Composites

The effect of simultaneous fiber surface treatment and matrix modification on mechanical properties of unidirectional ultra-high molecular weight polyethylene fiber/epoxy/nanoclay nanocomposites

Atomistic simulations of functionalization of aramid fiber‐epoxy nanocomposite

Specificity of the E-P state of the SR Ca-ATPase: implications for the coupling mechanism.