Abstract:The outstanding diffusivity and permeability of supercritical carbon dioxide (scCO2) are extremely beneficial for grafting reaction. In this work, aramid fibers (AF) are modified in scCO2 by glycidyl-polyhedral oliomeric silsesquioxane (POSS) with 2-ethyl-4-methylimidazole (2E4MZ) on the basis of cleaning with acetone. The surface morphology and chemical structure of the modified AF were measured and characterized by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), Scanning electron microscope (SEM), Thermogravimetric (TG), and Atomic force microscope (AFM). The interfacial shear strength (IFSS) was measured by a micro-bond pull-out test, then the modified AF/EP composites were prepared and the interlaminar shear strength (ILSS) was characterized. Research has shown that some of the glycidyl-POSS molecular chains permeated into the surface of the fiber and grafted onto the surface of the AF after modification, and the other glycidyl-POSS self-assembled on the surface of the fiber. XPS indicated the introduction of C–O and –COO–, which confirmed the existence of chemical reactions between AF and glycidyl-POSS. AFM and SEM images revealed that 2E4MZ, not only promoted the grafting reaction of glycidyl-POSS, but also intensified the self-assembly of glycidyl-POSS, both of which increased the roughness of the fiber. A monofilament tensile test and micro-bond pull-out test showed that there was a negative effect on the tensile strength after scCO2 processing. The tensile strength of modified AF, with glycidyl-POSS, increased the highest strength of 25.7 cN dtex−1, which was 8% higher than that of pristine AF. The improvement of ILS roughness and the polar chemical groups produced in grafting reaction. These results indicated that AF, treated in scCO2, with glycidyl-POSS, which is a suitable way of fiber modification, can significantly improve the surface adhesion of AF reinforced composites.

Construction of an Interfacial Layer of Aramid Fibers Grafted with Glycidyl POSS Assisted by Heat Treatment and Evaluation of Interfacial Adhesion Properties with Epoxy Resin

Functionalized Aramid Nanofibers Prepared by Polymerization Induced Self-Assembly for Simultaneously Reinforcing and Toughening of Epoxy and Carbon Fiber/epoxy Multiscale Composite

Enhancement of Para-Aramid Fibers by Depositing Poly-P-paraphenylene Terephthalamide Oligomer Modified Multi-Walled Carbon Nanotubes

Surface Modification of Aramid Fibers by Amino Functionalized Silane Grafting to Improve Interfacial Property of Aramid Fibers Reinforced Composite

Study on Surface Properties of Aramid Fiber Modified in Supercritical Carbon Dioxide by Glycidyl-POSS

Influence of Polyamide Acid Coating Reaction on the Properties of Aramid Fibre

Effects of oxidation‐induced aggregation structure transformation of aramid fiber on interfacial adhesion of epoxy resin

Preparation of highly active aramid fiber and effect on the interface property of aramid/epoxy composites

Rapid and Scalable Synthesis of Novel Carboxylated Aramid Nanofibers for Simultaneously Improving the Strength and Toughness of Carbon Fiber/epoxy Laminates

Non-destructive modification of aramid fiber by building nanoscale-coating solution to enhance the interfacial adhesion properties of the fiber-reinforced composites

Improved Interfacial Properties of Carbon Fiber/epoxy Composites Through Grafting Polyhedral Oligomeric Silsesquioxane on Carbon Fiber Surface

Influence of aramid fibers modified by glycidyl polyhedral silsesquioxane assisted with supercritical carbon dioxide on the properties of aramid fiber‐reinforced styrene butadiene rubber composites

Surface modification of aramid fiber by crystalline polyarylene ether nitrile sizing for improving interfacial adhesion with polyarylene ether nitrile

Latent active unit triggered crosslinking inside aramid fiber with improved transverse connection and composite properties

Characterization of fiber/matrix interfacial bonding strength of chemically grafted aramid fiber surface with epoxy resin composites

Layer-by-Layer Self-Assembly Strategy for Surface Modification of Aramid Fibers to Enhance Interfacial Adhesion to Epoxy Resin

Graphene Oxide-Modified Aramid Fibers for Reinforcing Epoxy Resin Matrixes

Interfacial properties of methacryl silsesquioxane modified carbon fiber/polyarylacetylene composites

A Facile Method to Prepare Nanoscale Polyacrylonitrile Particles Grafted Aramid Fibers for Superior Interfacial and Mechanical Properties of Epoxy Composites

Construction of double grafted interfacial layer to improve thermal and mechanical properties of short carbon fiber reinforced polyamide 6 composites

Effects of aramid nanofibers on the mechanical properties of epoxy resin and improved adhesion with aramid fiber