Abstract:Morphology development at the fiber/matrix interphase in fiber-reinforced isotactic polypropylene composites is a widely studied topic. While the application of shear flow may strongly enhance the nucleation density around the fiber, little is known about the influence of fibers on the crystallization of polypropylene subjected to an extensional flow. In this work, the flow around a single glass fiber upon uniaxial elongation of the melt is examined using X-ray scattering and diffraction techniques and compared to the response measured for the neat matrix. A comparison between a neat and compatibilized matrix is made given the strong influence of the addition of an adhesion modifier on the bulk crystallization kinetics of polypropylene. The flow is applied using an in-house-built filament stretching extensional rheometer, which, due to its midfilament control scheme, allows for in situ X-ray experiments. Combined small-angle X-ray scattering/wide-angle X-ray diffraction patterns are acquired during the flow and subsequent crystallization step. Postcrystallization area scans of the filament show that the introduction of a single glass fiber gives rise to the development of β-phase crystals, particularly in the area around the fiber ends, and in contrast to what is observed for the matrix materials alone, where solely α-phase is found. Surprisingly enough, the addition of a single fiber (0.00045 vol %) alters the crystallizing polymorph in almost the entire filament. However, the addition of the adhesion modifier hinders the formation of β-phase crystals around the fiber due to an acceleration of the bulk crystallization kinetics. Finite element simulations provide insight into the flow field around the fiber during stretching and demonstrate that the flow is no longer uniaxial extension, but dominated by shear, even though the volumetric amount of fiber as compared to the matrix is negligible. These findings explain the experimental observation of substantial β-phase formation after the introduction of a single fiber, while this is not observed in the matrix material. Worth noting, the formation of β-phase polypropylene depends not only on the presence and the strength of the flow but predominantly on the type of flow, i.e., shear as opposed to elongation.

Investigation on the Formation and Regulation of Yttrium Aluminosilicate Fiber Driven by Spontaneous Element Migration

Investigation of the Structural Environment and Chemical Bonding of Fluorine in Yb-doped Fluorosilicate Glass Optical Fibres

A Yttrium Aluminosilicate Glass Fiber with Graded Refractive Index Fabricated by Melt‐in‐tube Method

The Preparation of Yttrium Aluminosilicate (YAS) Glass Fiber with Heavy Doping of Tm3+ from Polycrystalline YAG Ceramics

Crystallization Behavior and IR Structure of Yttrium Aluminosilicate Glasses

Multi‐component yttrium aluminosilicate ( YAS ) fiber prepared by melt‐in‐tube method for stable single‐frequency laser

Growth and Characterization of Yb:Ho:YAG Single Crystal Fiber

Recent Advances in Fabrication and Applications of Yttrium Aluminum Garnet-Based Optical Fiber: A Review

Modeling of Advanced Melting Zone for Manufacturing of Optical Fibers

The oriented growth behavior of α-Al2O3 grains in alumina-mullite biphasic fibers

Experimental Research on Thermo-Direct Fiber Drawing Technique

A novel route to fabricate Yb:YAG ceramic fiber and its optical performance

Diffusion and Interface Effects during Preparation of All-Solid Microstructured Fibers

Fiber-Induced Crystallization in Elongational Flows

Formation, Element-Migration and Broadband Luminescence in Quantum Dot-Doped Glass Fibers

Control of temperature dependent viscosity for manufacturing of Bi-doped active fiber

Progress of Research on Preparation and Properties of Yttrium Aluminium Garnet Fibers

Fabrication and optical properties of Y2O3: Eu3+ nanofibers prepared by electrospinning.

A novel batch-scale fabrication method for hundred-micron YAG transparent ceramic fibers

3D Laser Engineering of Molten Core Optical Fibers: Toward a New Generation of Harsh Environment Sensing Devices

Spectroscopic and Laser Properties of Al-P Co-Doped Yb Silica Fiber Core-Glass Rod and Large Mode Area Fiber Prepared by Sol-Gel Method