Abstract:Bi2Te3-based materials are dominating thermoelectrics for almost all of the room-temperature applications. To meet the future demands, both their thermoelectric (TE) and mechanical properties need to be further improved, which are the requisite for efficient TE modules applied in areas such as reliable micro-cooling. The conventional zone melting (ZM) and powder metallurgy (PM) methods fall short in preparing Bi2Te3-based alloys, which have both a highly textured structure for high TE properties and a fine-grained microstructure for high mechanical properties. Herein, a mechanical exfoliation combined with spark plasma sintering (ME-SPS) method is developed to prepare Bi0.5Sb1.5Te3 with highly improved mechanical properties (correlated mainly to the dislocation networks), as well as significantly improved thermoelectric properties (correlated mainly to the texture structure). In the method, both the dislocation density and the orientation factor (F) can be tuned by the sintering pressure. At a sintering pressure of 20 MPa, an exceptional F of up to 0.8 is retained, leading to an excellent power factor of 4.8 mW m-1 K-2 that is much higher than that of the PM polycrystalline. Meanwhile, the method can readily induce high-density dislocations (up to ∼1010 cm-2), improving the mechanical properties and reducing the lattice thermal conductivity as compared to the ZM ingot. In the exfoliated and then sintered (20 MPa) sample, the figure-of-merit ZT = 1.2 (at 350 K), which has increased by about ∼20%, and the compressive strength has also increased by ∼20%, compared to those of the ZM ingot, respectively. These results demonstrate that the ME-SPS method is highly effective in preparing high-performance Bi2Te3-based alloys, which are critical for TE modules in commercial applications at near-room temperature.

Improvement of Thermoelectric Performance of Bi(2)Te(2.7)Se(0.3)via Grain Boundary Engineering with Melting KOH

Effective Atomic Interface Engineering in Bi2Te2.7Se0.3 Thermoelectric Material by Atomic-Layer-deposition Approach

Highly Distorted Grain Boundary with an Enhanced Carrier/Phonon Segregation Effect Facilitates High-Performance Thermoelectric Materials

Enhancing Thermoelectric Performance of n-Type Bi2Te2.7Se0.3 through Incorporation of Amorphous Si3N4 Nanoparticles

Atomic-scale Tuning of Oxygen-Doped Bi2Te2.7Se0.3 to Simultaneously Enhance the Seebeck Coefficient and Electrical Conductivity.

Enhancing thermoelectric performance of n-type Bi2Te2.7Se0.3 through the incorporation of MnSb2Se4 nanoinclusions

Construct Amorphous Polymer Interface to Enhance the Thermoelectric Performance of Commercial Bi0.5Sb1.5Te3 Materials

Enhanced thermoelectric performance and mechanical strength of n-type BiTeSe materials produced via a composite strategy

Enhancing the Thermoelectric Property of Bi2Te3 Through a Facile Design of Interfacial Phonon Scattering

Grain Boundary Engineering Enhances the Thermoelectric Properties of Y2Te3

Enhancing the room temperature thermoelectric performance of n-type Bismuth-telluride-based polycrystalline materials by low-angle grain boundaries

Thermoelectric Performance Enhancement in Commercial Bi0.5Sb1.5Te3 Materials by Introducing Gradient Cu-Doped Grain Boundaries

Achieving High Thermoelectric Performance by Introducing 3D Atomically Thin Conductive Framework in Porous Bi2Te2.7Se0.3‐Carbon Nanotube Hybrids

Improving the Performance of Thermoelectric Materials by Atomic Layer Deposition-based Grain Boundary Engineering

Optimizing Thermoelectric Performance of Hybrid Crystals Bi2O2Se1-xTex in the Bi2O2X System

Vacancy Manipulation by Ordered Mesoporous Induced Optimal Carrier Concentration and Low Lattice Thermal Conductivity in BixSb2- xTe3 Yielding Superior Thermoelectric Performance

Melt-Centrifuged (bi,sb)2 Te3 : Engineering Microstructure Toward High Thermoelectric Efficiency.

Enhancing the Thermoelectric and Mechanical Properties of Bi 0.5 Sb 1.5 Te 3 Modulated by the Texture and Dense Dislocation Networks

Achieving High Thermoelectric Performance by Introducing 3D Atomically Thin Conductive Framework in Porous Bi 2 Te 2.7 Se 0.3 ‐Carbon Nanotube Hybrids

Enhancement of thermoelectric performance in Mg 3 (Sb,Bi) 2 through engineered lattice strain and controlled carrier scattering

Enhanced Thermoelectric Performance Of (Sb0.75bi0.25)(2)Te-3 Compound From First-Principles Calculations