Abstract:Bi2Te3-based materials are dominating thermoelectrics for almost all of the room-temperature applications. To meet the future demands, both their thermoelectric (TE) and mechanical properties need to be further improved, which are the requisite for efficient TE modules applied in areas such as reliable micro-cooling. The conventional zone melting (ZM) and powder metallurgy (PM) methods fall short in preparing Bi2Te3-based alloys, which have both a highly textured structure for high TE properties and a fine-grained microstructure for high mechanical properties. Herein, a mechanical exfoliation combined with spark plasma sintering (ME-SPS) method is developed to prepare Bi0.5Sb1.5Te3 with highly improved mechanical properties (correlated mainly to the dislocation networks), as well as significantly improved thermoelectric properties (correlated mainly to the texture structure). In the method, both the dislocation density and the orientation factor (F) can be tuned by the sintering pressure. At a sintering pressure of 20 MPa, an exceptional F of up to 0.8 is retained, leading to an excellent power factor of 4.8 mW m-1 K-2 that is much higher than that of the PM polycrystalline. Meanwhile, the method can readily induce high-density dislocations (up to ∼1010 cm-2), improving the mechanical properties and reducing the lattice thermal conductivity as compared to the ZM ingot. In the exfoliated and then sintered (20 MPa) sample, the figure-of-merit ZT = 1.2 (at 350 K), which has increased by about ∼20%, and the compressive strength has also increased by ∼20%, compared to those of the ZM ingot, respectively. These results demonstrate that the ME-SPS method is highly effective in preparing high-performance Bi2Te3-based alloys, which are critical for TE modules in commercial applications at near-room temperature.

Enhanced Thermoelectric Performance Of (Sb0.75bi0.25)(2)Te-3 Compound From First-Principles Calculations

Highly Enhanced Thermoelectric and Mechanical Properties of Bi-Sb-Te Compounds by Carrier Modulation and Microstructure Adjustment

Unraveling electronic origins for boosting thermoelectric performance of p-type (Bi,Sb) 2 Te 3

Synergistic Texturing and Bi/Sb‐Te Antisite Doping Secure High Thermoelectric Performance in Bi 0.5 Sb 1.5 Te 3 ‐Based Thin Films

Integrating band engineering with point defect scattering for high thermoelectric performance in Bi2Si2Te6

Synergistic modulation of mobility and thermal conductivity in (Bi,Sb)2Te3 towards high thermoelectric performance

Enhancement on thermoelectric performance by Ti doping and vacancies

High-Performance p-Type Bi 2 Te 3 -Based Thermoelectric Materials Enabled via Regulating Bi-Te Ratio

Thermoelectric Performance of Binary Lithium-Based Compounds: Li3Sb and Li3Bi

Realizing High Thermoelectric Performance in Cu2Te Alloyed Cu1.15In2.29Te4

Optimized Thermoelectric Properties of Bi0.48Sb1.52Te3 Through AgCuTe Doping for Low-Grade Heat Harvesting.

Enhanced Thermoelectric Performance of Bi–Se Co-Doped Cu1.8S Via Carrier Concentration Regulation and Multiscale Phonon Scattering

Thermoelectric Performance Enhancement in Commercial Bi0.5Sb1.5Te3 Materials by Introducing Gradient Cu-Doped Grain Boundaries

Improved thermoelectric and mechanical performance of Sb2Te3-based materials toward the segmented operation

Tuning Ag content to achieve high thermoelectric properties of Bi-doped p-type Cu3SbSe4-based materials

Low Lattice Thermal Conductivity Induced by Antibonding Sp-Hybridization in Sb2Sn2Te6 Monolayer with High Thermoelectric Performance: First-principles Calculations

Thermoelectric Cu-doped (Bi,sb)(2)te-3: Performance Enhancement and Stability Against High Electric Current Pulse

Enhancement of thermoelectric properties over a wide temperature range by lattice disorder and chemical potential tuning in a (CuI) y (Bi2Te3)0.95- x (Bi2Se3) x (Bi2S3)0.05 quaternary system

Regulation of exciton for high thermoelectric performance in (Bi, Sb)2Te3 alloys via doping with Pb and multi-scale microstructure

High performance of Mg3Bi1.5Sb0.5 based materials for power generation: Revealing the counter-intuitive effect of tuning Bi content on the thermoelectric properties

Enhancing the Thermoelectric and Mechanical Properties of Bi 0.5 Sb 1.5 Te 3 Modulated by the Texture and Dense Dislocation Networks