Abstract:Laser metal deposition (LMD) additive manufacturing process was applied to produce ultrafine TiC particle reinforced Inconel 625 composite parts. The effects of laser energy input per unit length (LEIPUL) on microstructure development, densification response, and mechanical performance including wear performance and tensile properties were comprehensively studied. A relationship of processing conditions, microstructural characteristics, mechanical performance, and underlying strengthening mechanisms was proposed for a successful LMD of high-performance Inconel based composite parts. It revealed that using an insufficient LEIPUL of 33kJ/m lowered the densification behavior of LMD-processed parts, due to the appearance of residual large-sized pores in inter-layer areas of the parts. An increase in LEIPUL above 100kJ/m yielded the near fully dense composite parts after LMD. On increasing LEIPUL, the TiC reinforcing particles became significantly refined and smoothened via the elevated melting of particle surfaces and the dispersion state of ultra-fine reinforcing particles was homogenized due to the efficient action of Marangoni flow within the molten pool. The dendrites of Ni–Cr γ matrix underwent a successive change from an insufficiently developed, disordered microstructure to a refined, ordered microstructure with the increase of LEIPUL. However, the columnar dendrites of the matrix were coarsened apparently at an excessive LEIPUL of 160kJ/m because of the elevated thermalization of the input laser energy. The formation of the refined columnar dendrites of Ni–Cr γ matrix combined with the homogeneously distributed ultra-fine reinforcing particles contributed to the enhancement of wear performance of LMD-processed composites with a considerably low coefficient of friction (COF) of 0.30 and reduced wear rate of 1.3×10−4mm3/Nm. The optimally prepared TiC/Inconel 625 composite parts demonstrated a ductile fracture mode with a sufficiently high tensile strength of 1077.3MPa, yield strength of 659.3MPa, and elongation of 20.7%. The superior tensile properties of LMD-processed parts were attributed to the significant grain refinement effect of the matrix during laser processing and the efficient prohibition of ultrafine reinforcing particles on the mobility of dislocations.

Influence of Thermal Behavior along Deposition Direction on Microstructure and Microhardness of Laser Melting Deposited Metallic Parts

Thermodynamic Behavior and Microstructure Evolution of Inconel 718 Alloy by Laser Metal Deposition

Influence of pulsed laser scanning patterns on microstructural evolution and mechanical properties of Inconel 718 in direct laser deposition

The microstructural evolution and mechanical response of laser direct energy deposition Inconel 718 alloy based on simulation and experimental methods

Thermal-fluid dynamic behavior and its effect on particle distribution and solidification characterization during the laser melting deposition of Ti-based composites

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Laser Additive Manufacturing of Ultrafine Tic Particle Reinforced Inconel 625 Based Composite Parts: Tailored Microstructures and Enhanced Performance

Thermal behavior and microstructure evolution mechanism of W-20%Fe alloy fabricated by laser metal deposition

Laser metal deposition of thin-walled parts of Al 0.8 CrFe 2 Ni 2 high-entropy alloy: Process window, microstructure, wear resistance and mechanical anisotropy

Effect of Laser Beam Profile on Thermal Transfer, Fluid Flow and Solidification Parameters during Laser-Based Directed Energy Deposition of Inconel 718

Effect of discrete deposition and segregated heat-treatment on the macro- and microstructure, and tensile properties of large-scale titanium alloy components by laser melting deposition

Influence of processing parameters on the thermal history, microstructure and tensile properties of Inconel 738 produced by laser directed energy deposition

Effect of heat treatment on microstructure, precipitation behavior and mechanical properties of Inconel 718 fabricated by laser direct energy deposition

Effect of laser lower and remelting on the microstructure and tribological properties of GH3230 superalloy coating fabricated by laser melting deposition

Influences of Cooling Conditions on the Liquation Cracking in Laser Metal Deposition of a Directionally Solidified Superalloy

Effect of laser direct metal deposition process on the microstructure and mechanical properties and temperature and stress fields of 24CrNiMo

Modeling of Temperature Field Evolution During Multilayered Direct Laser Metal Deposition

Role of angular velocity on Marangoni convection shifting, heat accumulation, and microstructure evolution using laser directed energy deposition

Solidification Microstructure Prediction of Ti-6Al-4V Alloy Produced by Laser Melting Deposition

Effects of Process Parameters on Microstructures and Tensile Properties of Laser Melting Deposited CrMnFeCoNi High Entropy Alloys

Laser Metal Deposition of TiC/Inconel 718 Composites with Tailored Interfacial Microstructures