Abstract:The effects of compression deformation of gas diffusion layer (GDL) on the performance of a proton exchange membrane fuel cell (PEMFC) with serpentine flow field were numerically investigated by coupling two-dimensional GDL mechanical deformation model based on Finite Element Analysis and three-dimensional two-phase PEMFC model with incorporating the deformation impacts. Emphasis is located on exploring the influences of assembly pressure on the non-uniform geometric deformation and distributions of transport properties in the GDL, flow behaviors and local distributions of oxygen and current density, cell polarization curves and net power densities of the PEMFC. It was indicated that the non-uniform deformation of GDL results in inhomogeneous distributions of porosity and permeability in the GDL due to the presence of rib-channel pattern, and the transport properties in the under-rib region are greatly reduced with increasing the assembly pressure, consequently weakening the gas flow and oxygen transport in the under-rib region and increasing the non-uniformity of local current density distribution. As for the overall cell performance, however, attributed to the tradeoff between the adverse impacts of GDL compression on mass transport loss and positive effects on reducing ohmic loss, the overall cell performance is firstly increased and then decreased with increasing assembly pressure from 0 MPa to 5.0 MPa, and the maximum cell performance can be achieved at the assembly pressure of about 1.0 MPa for all cases studied. As compared with the case for zero assembly pressure, the maximum net power density of the cell can be improved by about 7.7%, 9.9%, 10.5% and 10.7% for the cathode stoichiometry ratios of 2.0, 3.0, 4.0 and 5.0@i(ref) = 1 A.cm(-2), respectively. Practically, it is suggested that the assembly pressure is controlled in an appropriate range of 0.5 MPa-1.5 MPa such that the cell net power can be boosted and pressure head requirement for the pump can be maintained in a appropriate level. (C) 2019 Hydrogen Energy Publications LLC. Published by Elsevier Ltd. All rights reserved.

Pressure Effect on the PEMFC Performance

Analyze the Effects of Flow Mode and Humidity on PEMFC Performance by Equivalent Membrane Conductivity

Effect of cathode relative humidity on membrane water content and performance of PEMFC

The Optimization of PEM Fuel Cell Performance Using the CFD Method Combined with Experimental Validation

Influence of Operating and Electrochemical Parameters on PEMFC Performance: A Simulation Study

The Effects of Cathode Platinum Loading and Operating Backpressure on PEMFC Performance

Reaction Gas Pressure, Temperature, and Membrane Water Content Modulate Electrochemical Process of a PEMFC: A Simulation Study

Experimentally and Numerically Investigating Cell Performance and Localized Characteristics for a High-Temperature Proton Exchange Membrane Fuel Cell

Study on the Effect of Temperature on Pressure Drop and Under-Rib Convection in PEMFC

Effects of Cathode Gas Diffusion Layer Porosity and Contact Angle Distributions along Through-Plane Direction on the Performance of Polymer Electrolyte Membrane Fuel Cell

Three-dimensional Modeling of a PEMFC with Serpentine Flow Field Incorporating the Impacts of Electrode Inhomogeneous Compression Deformation

Improvement of Thermal and Water Management of Air-Cooled Polymer Electrolyte Membrane Fuel Cells by Adding Porous Media into the Cathode Gas Channel

CFD investigating the effects of different operating conditions on the performance and the characteristics of a high-temperature PEMFC

Assembly pressure and membrane swelling in PEM fuel cells

Modeling of the Effects of Cathode Catalyst Layer Design Parameters on Performance of Polymer Electrolyte Membrane Fuel Cell

Influence of clamping pressure on contact pressure uniformity and electrical output performance of proton exchange membrane fuel cell

Effect of Assembly Pressure on the Performance of Proton Exchange Membrane Fuel Cell

Numerical Modeling and Performance Prediction of Water Transport for PEM Fuel Cell

Modeling Analysis of Polymer Electrolyte Membrane Fuel Cell with Regard to Oxygen and Charge Transport under Operating Conditions and Hydrophobic Porous Electrode Designs

Comparison of Self-Humidification Effect on Polymer Electrolyte Membrane Fuel Cell with Anodic and Cathodic Exhaust Gas Recirculation

The Dynamic Behavior of Pressure During Purge Process in the Anode of A Pem Fuel Cell