Abstract:In an electrostatic precipitator, particles migrate to the collecting plates through electrostatic force. Simultaneously, the effect of gravity and hydrodynamic drag force will cause these particles to vacate the plates. Emission concentration and removal efficiency gradually stabilize after the particles pass through multiple electric fields, and this stability value determines the high limit of electrostatic precipitation capacity. In this study, the balance between particle electrostatic trapping and air re-entrainment was investigated through a closed-loop electrostatic precipitator system, and the behavior of the particles deposited into the collecting plates was qualitatively analyzed. The particle emission concentration was reduced significantly when residence time was within 40 s. The particle concentration reached its limit and remained relatively stable after remaining stable for 100 s in the electric field. The applied voltage, velocity of flow, and temperature are the influencing factors considered in this study, here it was found that the decreased flow velocity, temperature and rising voltage were benefiting to particles removal efficiency. The ultimate emission concentration gradually decreased from 13.14 mg/m(3) to 7.19 mg/m(3) while the velocity of the flow decreased from 0376 m/s to 0240 m/s at the temperature of 700 K. The ultimate emission concentration gradually increased from 6.24 mg/m(3) to 1.79 mg/m(3) while the temperature decreased from 800 K to 400 K when the flue gas velocity was 0376 m/s, and the applied voltage was at its maximum which can be used at the corresponding temperature. The ultimate emission concentration gradually decreased from 19.5 mg/m(3) to 6.0 mg/m(3) when the flue gas temperature was 400 K, and the velocity of the flow was 0376 m/s, with the increase in voltage from 14.9 kV to 32.5 kV. In addition, particles of different size segments and specific resistances exhibited various characteristics in this study because the electrostatic and van der Waals forces were significantly affected by the particle size. (C) 2018 Elsevier B.V. All rights reserved.

Research on Resistance Characteristics of Electrostatic Precipitator's Perforated Plates With Medium and High Porosity

Experimental study on resistance characteristics of perforated plates with medium and high porosity in high temperature condition

Characterization of Electrohydrodynamic Flow in a Plate-Plate Electrostatic Precipitator with a Wire-Cylinder Pre-Charger by Data-Driven Vortex and Residence Time Analysis

Electrode Configurations Inside an Electrostatic Precipitator and Their Impact on Collection Efficiency and Flow Pattern

A Numerical Study on the Air-Side Heat Transfer of Perforated Finned-Tube Heat Exchangers with Large Fin Pitches

Research on Flow Uniformity and Pressure Characteristics of a Wide-angle Electrostatic Precipitator

Electrode Geometry Optimization in Wire-Plate Electrostatic Precipitator and Its Impact on Collection Efficiency

Study of Pressure Drop-Flow Rate and Flow Resistance Characteristics of Heated Porous Materials under Local Thermal Non-Equilibrium Conditions

Study on heat transfer and friction characteristics in fin-tube heat exchangers used for electrical machines cooling

An Experimental Study on the Air Side Heat Transfer Performance of the Perforated Fin-Tube Heat Exchangers under the Frosting Conditions

Aerodynamics Analysis of Superheated Steam Flow Through Multi-Stage Perforated Plates

Numerical analysis of turbulence field and particle trajectory inside wet Electrostatic Precipitator

Theoretical and Experimental Investigation of Flow Rate Characteristics of Sintered Metal Porous Media

Experimental Research on Particulate Collection Performanceby Perforated Plate in Hybrid Particulate Collector

Analysis of heat transfer and flow resistance characteristics in perforated fin

Development and Experimental Investigation of the Narrow-Gap Coated Electrostatic Precipitator with a Shield Pre-Charger for Indoor Air Cleaning

Numerical Simulation of Air Distribution Plate at the Inlet of Wet Electrostatic Precipitator

Research of the effect of different corrugated dust collection plates on particle removal in electrostatic precipitators

Effect of High-Voltage Electrostatic Precipitator Dust Collection Plate Structure on Collection Efficiency

Balance and Stability Between Particle Collection and Re-Entrainment Inawide Temperature-Range Electrostatic Precipitator

Investigation Of Precipitation Fouling In Corrugated Plate Heat Exchangers