Abstract:Statement of problem: Failure of a fiber post and composite resin core often occurs at the junction between the 2 materials. This failure process requires better characterization. Purpose: The purpose of this study was to evaluate the effect of 2 chemical solvents, hydrogen peroxide and methylene chloride, on the shear bond strength of quartz and glass fiber posts to a composite resin. Material and methods: Twenty-four posts (3 +/-0.1 mm in length) were prepared for each quartz (LIGHT-POST (LP)) and glass fiber (Cytec blanco (CB)) post. Posts were horizontally embedded in acrylic resin with half of the post diameter exposed. The exposed surfaces were successively ground with 400-, 800-, and 1200-grit silicon carbide papers, to ensure uniform smoothness. The specimens were divided into 3 subgroups (n=8) representing different surface treatment techniques, including application of silane for 60 seconds (S), etching with hydrogen peroxide for 20 minutes (H), and etching with methylene chloride for 5 seconds (M). Silane-treated specimens served as controls. A dual-polymerized composite resin (Tetric EvoCeram) was placed in a polytetrafluoroethylene mold (30 x 2 mm) positioned upon the post specimens and polymerized for 20 seconds with a light-emitting diode (LED) polymerization unit. The specimens were stored in water at 37 degrees C for 24 hours. Shear bond strength values (MPa) of posts and composite resin cores were measured using a universal testing machine with a crosshead speed of 0.5 mm/min. Data were analyzed by 2-way analysis of variance (ANOVA). Post hoc Tukey intervals for comparison among the 2 post materials and 3 surface treatment techniques were calculated (alpha =.05). The effect of the chemical surface treatments on glass and quartz fiber post surfaces were examined with a scanning electron microscope (SEM). Results: There were significant differences between the shear bond strength for LP and CB (P<.001). For all groups, the application of H showed the highest bond strength values. There was no significant difference between the S and M groups (P>.05). The SEM observations demonstrated that the fiber post surfaces were modified after chemical surface treatment techniques. Conclusions: The surface treatment of quartz and glass fiber posts with hydrogen peroxide significantly enhanced the shear bond strength of the composite resin tested due to its ability to dissolve the epoxy resin matrix used in each post. The lowest bond strength was obtained with M and S groups. Application of methylene chloride to the fiber post surfaces for 5 seconds was not effective in increasing the shear bond strength of the fiber post to composite resin.

Influence of Surface Treatment on the Interfacial and Mechanical Properties of Short S-Glass Fiber-Reinforced Dental Composites

Effects of Different Surface Treatments of Woven Glass Fibers on Mechanical Properties of an Acrylic Denture Base Material

Surface modifications of short quartz fibers and their influence on the physicochemical properties and in vitro cell viability of dental composites

Surface Treatment Effect on the Mechanical and Thermal Behavior of the Glass Fabric Reinforced Polysulfone

The Study of the Glass Fiber Surface Treatment Effect on the Base Strength Characteristics of the Composite Material

Semi-interpenetrating Interfacial Formation of Glass Fiber Reinforced Dental Resin Bio-Composites and Its Mechanical Properties

Pre-use Interfacial Shear Strength Prediction for Fiber-Reinforced Thermosetting Composites Based on Stress-Impedance Effect of Ferromagnetic Microwires

Mechanical properties and fracture behavior of flowable fiber reinforced composite restorations

Surface treatments of a glass-fiber reinforced composite: Effect on the adhesion to a composite resin

Preparation and Characterization of Sodium Aluminum Silicate-Polymer Composites and Effects of Surface Roughness and Scratch Directions on Their Flexural Strengths

Effect of E-glass fibers addition on compressive strength, flexural strength, hardness, and solubility of glass ionomer based cement

Effects of chemical surface treatments of quartz and glass fiber posts on the retention of a composite resin

Properties of discontinuous S2-glass fiber-particulate-reinforced resin composites with two different fiber length distributions

Enhanced interfacial and mechanical properties of glass fabric/epoxy composites via grafting silanized carbon nanotubes onto the fibers

Mechanical Strength Behaviour of Silane Treated E-glass Fibre/Al 6061 & SS-304 Wire Mesh Reinforced Epoxy Resin Hybrid Composite

Mechanical, morphological and wear resistance of natural fiber / glass fiber-based polymer composites

Characterization of fiber/matrix interfacial bonding strength of chemically grafted aramid fiber surface with epoxy resin composites

Effect of fiber surface treatment with silane coupling agents and carbon nanotubes on mechanical properties of carbon fiber reinforced polyamide 6 composites

Flexible Fiber-Reinforced Composites with Improved Interfacial Adhesion by Mussel-Inspired Polydopamine and Poly(methyl Methacrylate) Coating

Surface treatment of glass fiber and carbon fiber posts: SEM characterization

Chemical Surface Modification Methods of Resin Composite Repaired with Resin-Modified Glass-Ionomer Cement