Abstract:PURPOSEHigh-sensitivity and high-resolution depth-encoding positron emission tomography (PET) detectors are required to simultaneously improve the sensitivity and spatial resolution of a PET scanner so that the quantitative accuracy of PET studies can be improved. The semi-monolithic scintillator PET detector has the advantage of measuring the depth of interaction with single-ended readout as compared to the traditional pixelated scintillator detector, and significantly reducing the edge effect that deteriorates the spatial resolution at edges of the detector as compared to the monolithic scintillator detector if a long rectangular semi-monolithic detector is used. In this work, depth-encoding PET detector modules were built by using long rectangular semi-monolithic scintillators and single-ended readout by silicon photomultiplier (SiPM) arrays. The performance of the detector modules was measured.METHODSThe rectangular semi-monolithic scintillator detector has an outside dimension of 11.6 × 37.6 × 10 mm3 and consists of 11 polished lutetium-yttrium oxyorthosilicate (LYSO) slices measuring 1 × 37.6 × 10 mm3 . The enhanced specular reflector (ESR) was glued on both cross-sectional surfaces of each crystal slice. For the face opposite to the SiPM array and the two end faces of the detectors, surface treatments with and without black paint were implemented for performance comparison. The bottom face of the semi-monolithic detector was coupled to a 4 × 12 SiPM array that was grouped along rows and columns separately into 16 signals. The four row signals were used to identify the slices, and the 12 column signals were used to estimate the y (monolithic direction) and z (depth direction) interaction positions. The detector was irradiated at multiple positions with a collimated 511 keV gamma beam. The collimated beam was obtained with electronic collimation by using a 22 Na point source and a reference detector. The estimated width of the gamma beam is around 0.5 mm. The flood histogram for crystal slices was measured by using the center of gravity (COG) method. The COG method and the squared COG method were used for y position estimation. The standard deviation of the column signals, the ratio of maximum to the sum of the column signals, and the sum of squared column signals were used for z position estimation.RESULTSAll slices were clearly resolved from the measured flood histograms for both detectors with different crystal surface treatments. The estimated y positions roughly linearly change with the true positions at the middle of the detector until ~5 mm from both ends of the detector. The y and z spatial resolutions of the detectors were estimated for all middle positions located more than 5 mm from both ends of the detector. The squared COG method provides better y position resolution than the COG method. The three z estimation methods provide similar depth of interaction (DOI) resolution. Surface treatment with black paint significantly improves both y and z position resolution but degrades the energy and timing resolution of the detectors. The average full width half maxima (FWHM) spatial resolution is improved from 1.77 to 1.07 mm in the y direction by using the squared COG method and from 2.71 to 1.55 mm in the z direction by using the standard deviation method. The slice-based average energy resolution degrades from 15.8% to 24.9%. The timing resolution of the entire detector module degrades from 596 to 788 ps.CONCLUSIONThe performance of rectangular semi-monolithic scintillator PET detectors with two different crystal surface treatments was measured. The detectors provide superior spatial resolution and depth-encoding capability and can be used to develop small animal and dedicated breast and brain PET scanners that can simultaneously achieve high spatial resolution, high sensitivity, and low cost.

A preclinical PET detector constructed with a monolithic scintillator ring.

A thick semi-monolithic scintillator detector for clinical PET scanners

Evaluation of a PET detector based on SiPMs and FPGA-only MVT digitizers

DESIGN OF A NEW DEPTH ENCODING DETECTOR FOR PET

Scintillation and Cherenkov photon counting detectors with analog silicon photomultipliers for TOF-PET

Development of an MR-compatible DOI-PET Detector Module

Performance of Long Rectangular Semi‐monolithic Scintillator PET Detectors

Performance of a SiPM Based Semi-Monolithic Scintillator PET Detector

Evaluation of a PET Detector for a Next Generation Preclinical PET/EPRI

Construction and evaluation of a large radiation detector for Positron Emission Tomography applications

A Prototype MR Insert PET Detector with Strip-Line Readout

A Semi-Monolithic Detector providing intrinsic DOI-encoding and sub-200 ps CRT TOF-Capabilities for Clinical PET Applications

A Finely Segmented Semi-Monolithic Detector tailored for High Resolution PET

Validation of the design of a high-sensitivity and high-resolution PET system for a preclinical PET/EPR hybrid scanner

High Spatial Resolution and High Sensitivity Three Dimensional PET Detector Development with Position-sensitive Avalanche Photodiode and Silicon Photomultiplier Readout

A High Count-Rate and Depth-of-Interaction Resolving Single Layered One-Side Readout Pixelated Scintillator Crystal Array for PET Applications

Optimization of a depth of interaction encoding PET block detector for a PET/MRI insert

A compact PET detector module using SiPMs and MVT digitizers

Development of Depth Encoding Small Animal PET Detectors Using Dual-Ended Readout of Pixelated Scintillator Arrays with SiPMs

Development of a MR-compatible DOI-TOF detector module for PET imaging systems

A Novel Sub-Millimeter Resolution Pet Detector with Tof Capability