Abstract:In recent years, the popularity of high-power equipment such as electric vehicles demands a higher the energy density, higher the power density, and low cost in lithium-ion batteries (LIBs). The capacity of LIBs is typically limited by the cathode. For example, in LIBs based on LiCoO 2 //graphite system, which have achieved great success in commercialization, the reversible capacity of LiCoO 2 (~137 mAh g -1 ) is lower than that of graphite (~370 mAh g -1 ) [1]. Hence, it is necessary to improve the capacity of the cathode in order to improve the performance of LIBs. Among the cathode materials, Vanadium pentoxide (V 2 O 5 ) is considered as one of the ideal next-generation electrode materials due to its high theoretical capacities (294 mAh g -1 ), high energy densities, good safety and low cost [2]. Nevertheless, its cycle performance and poor rate-capability caused by severe structural changes during the repeated lithiation/de-lithiation, slow diffusion of lithium ion (Li + ), and low electrical conductivity hinders its commercialization [2]. Various attempts to fabricate the nanostructured V 2 O 5 such as nanorods, nanobelts, nanosheet, and hollow spheres have been pursued to remedy the issues. The nanostructures are used to overcome their kinetic limitation by reduction of Li + ion diffusion distance and increase in the electrode/electrolyte contact area. In nanostructures, however, structural collapse and particles agglomeration could emerge during Li + ion penetration procedure [3]. In particular, many studies have focused on the 1D nanostructured V 2 O 5 in length along [010], the fastest growth direction of V 2 O 5 , because of its simplicity in synthesis [4]. However, 1D-nanostructured V 2 O 5 has long Li + ion diffusion distance along [010] direction, which is corresponding to the energy preferred Li + ion diffusion path [5]. 1D diffusion along the short [010] direction in V 2 O 5 can be the fast Li + ion diffusion path for cathode in LIBs. Therefore, to design an optimal structure for V 2 O 5 as cathode materials, the following conditions should be satisfied: i) structures consisted of primary nanostructured units to prevent agglomeration. ii) a short [010] length with high percentage of exposed (010) facets to shorten a Li + ion diffusion path and facilitate the Li + ion intercalation reactions. In this context, we fabricated nanoplates–stacked V 2 O 5 (Li-treated VO) through Li-treatment method in hydrothermal synthesis followed by heat treatment. Li + ions from lithium nitrate (LiNO 3 ), which is added to precursor solution, can inhibit the completely phase transition from xerogel to crystal during hydrothermal process, leading to formation of xerogel/crystal composite. During following heat treatment process, the cleavage and oriented attachment mechanism are accompanied, evolving nanoplates–stacked V 2 O 5 with short [010] length and highly exposed (010) facets (Figure 1). The Li-treated VO electrodes could facilitate the fast and efficient transportation of Li + ion into the [010] channel. In particular, the Li-treated VO electrodes can achieve a reversible capacity of 252 mAh g -1 at 50 mA g -1 in the voltage range of 2.05–4.0 V (vs. Li/Li + ) (Figure 2). Notably, the Li-treated VO electrodes also exhibit a higher rate performance (140 mAh g -1 at 1 A g -1 (Figure 2)) and cycling capability (79 % capacity retention after 100 cycles (Figure 3)) compared to untreated V 2 O 5 nanobelt (VO) electrodes. In addtion, the reversible lithium intercalation reaction and structure stability of Li-treated VO are confirmed by further analyses. Figure 1

Excellent Cycling Stability and Capability of Novel Mixed-Metal Vanadate Coated with V2O5 Materials in an Aqueous Solution

Improved cycling performance of polypyrrole coated potassium trivanadate as an anode for aqueous rechargeable lithium batteries

Enhanced electrochemical performance of LiV2O4-coated and V4+-doped LiNi0.8Co0.1Mn0.1O2 cathode for lithium-ion batteries

Rich Alkali Ions Preintercalated Vanadium Oxides for Durable and Fast Zinc-Ion Storage

Improved electrochemical performance of layered Li1.2Ni0.13Co0.13Mn0.54O2 cathode material via VPO5 coating

Freestanding Sodium Vanadate/Carbon Nanotube Composite Cathodes with Excellent Structural Stability and High Rate Capability for Sodium-Ion Batteries

Improvement of Electrochemical Properties of LiNi1/3Co1/3Mn1/3O2 by Coating with V2O5 Layer

Electrochemically Anodized V 2 O 5 as an Efficient Sodium Cathode

Reconstructing Vanadium Oxide with Anisotropic Pathways for a Durable and Fast Aqueous K-Ion Battery

Superior Cycling Performance Of A Novel Nkvo@Polypyrrole Composite Anode For Aqueous Rechargeable Lithium-Ion Batteries

Structural Engineering of Hydrated Vanadium Oxide Cathode by K+ Incorporation for High-Capacity and Long-Cycling Aqueous Zinc Ion Batteries

An elaborate insight of lithiation behavior of V2O5 anode

110Th Anniversary: Concurrently Coating and Doping High-Valence Vanadium in Nickel-Rich Lithiated Oxides for High-Rate and Stable Lithium-Ion Batteries

Electrochemical Performance and Thermal Stability of Li₁.₁₈Co₀.₁₅Ni₀.₁₅Mn₀.₅₂O₂ Surface Coated with the Ionic Conductor Li₃VO₄

Nanoplates-Stacked Vanadium Oxide Cathode Employing Higher Kinetics and Stability in a Lithium-Ion Battery

Synthesis and Electrochemical Performance of KVO/GO Composites as Anodes for Aqueous Rechargeable Lithium-Ion Batteries

Enhanced Stability of Vanadium-Doped Li1.2Ni0.16Co0.08Mn0.56O2 Cathode Materials for Superior Li-ion Batteries

Mixed metal engineering of V2O3 hollow nanoprisms encapsulated in N-doped carbon as anode for high-performance lithium-ion storage

Conductive Polymer-Modified Sodium Ion Intercalation in Vanadium Pentoxide for High Performance Zinc-Based Batteries

Facile Synthesis and Electrochemical Analysis of Zn-Doped V2O5 Anode Materials for High-Rate Li Storage

Improvement of cycle performance of the high nickel cathode material LiNi0.88Co0.07Al0.05O2 for lithium-ion batteries by the spray drying of V2O5