Abstract:This study systematically investigates the influence of the composite addition of Ce, La, and Ca elements on the microstructure evolution and mechanical properties of Mg-3Zn-1Mn/Sn (wt.%) alloys. It indicates that the strength of Mg-Zn-Mn series alloys is superior to that of Mg-Zn-Sn series alloys, due to the stronger restriction of nanosized Mn particles on the recrystallization process and grain growth compared with Mg2Sn phases. The addition of the Ca-La-Ce elements significantly enhances the strength of the Mg-3Zn-1Sn alloy (YS increased by approximately 92.5%, UTS increased by approximately 29.2%, and EL decreased by nearly 52.2%), while for the Mg-3Zn-1Mn alloy, a balanced effect on both the strength and performance can be achieved. This difference mainly lies in the more pronounced refined effect on the grain size and the formation of a bimodal grain structure with strip-like un-DRXed grains and surrounding fine DRXed grains for the Mg-3Zn-1Sn alloy. In contrast, the addition of the Ca-La-Ce elements has a less obvious hindrance on the recrystallization process in the Mg-Zn-Mn series alloy, while significantly weakening the extrusion texture while refining the grains. Through in-depth characterization and experimental analysis, it is found that Sn and Ca can promote the formation of brittle and fine secondary phases. A nanoscale Sn phase (Mg2Sn phase) is more likely to accumulate at the grain boundaries, and the size of the nanoscale Ca2Mg6Zn3 in Mg-Zn-Mn series alloys is finer and more dispersed than that in Mg-Zn-Sn series alloys, thus strongly hindering recrystallization and refining the recrystallized structure of the alloy.

Effects of B and Sn Additions on the Microstructure and Mechanical Property of Mg-3Al-1Si Alloy

Effect of Sn Addition on the Microstructure and Mechanical Properties of AZ31 Alloys

Influence of Al Addition on the Microstructure and Mechanical Properties of Mg-Zn-Sn-Mn-Ca Alloys

Improving mechanical properties of Mg-Sn alloys by co-addition of Li and Al

Effect of Ca addition on microstructure and mechanical properties of Mg–3.8Al–1.1Sn alloys

Sn-Sc microalloying-induced property improvement and micromechanisms of an Al-Mg-Si alloy

Effects of Sn and Mn Addition on the Microstructure and Mechanical Properties of As-Extruded Mg–2Al–1Zn Alloys

Effect of Sn content on microstructure and tensile properties of as-cast and as-extruded Mg−8Li−3Al−(1,2,3)Sn alloys

Regulating the Microstructure and Mechanical Properties in Cast Al–3Li–2Cu-0.15Zr Alloy Via Sn Addition and Heat Treatment

Enhanced Mechanical Properties and Isotropy of Mg-2Al-0.8Sn Alloy through Ca Addition

Microstructure and Mechanical Properties of Magnesium Alloy Az61with 1%sn Addition

Influence of Si Addition on the Microstructure and Mechanical Behaviour of Mg-5Sn-3Zn-1Mn Alloy

Improving the Mechanical Properties and Intergranular Corrosion Resistance of Al-9.2Mg-0.8Mn-0.2Zr Alloy by Sn Addition

Effect of Al on the Microstructure and Mechanical Properties of Mg–Sn–Ca–Mn Wrought Alloy

Effect of Mg2sn Intermetallic on the Grain Refinement in As-Cast Am Series Alloy

Comparative Study on Mechanical Properties and Microstructure Evolution of Mg-3Zn-1Mn/Sn Alloy through Ca-La-Ce Addition

Effect of a Trace Addition of Sn on the Aging Behavior of Al–Mg–Si Alloy with a Different Mg/Si Ratio

Effects of Sm Addition on Microstructure and Mechanical Properties of Mg–6Al–0.6Zn Alloy

The Effects of Silicon Addition on the Microstructure and Mechanical Properties of a Mg-Al-Sn Alloy Produced by Vacuum Assisted High Pressure Die Casting

Effect of Mischmetal Addition on Microstructure and Mechanical Properties of As-Cast and As-Rolled Mg–Sn–Ca Alloys

Microstructure, Mechanical Properties and First Principle Calculation of Mg-7Al (-2Sn) Alloys Prepared by Vacuum Die-casting