Abstract:Poly(methylmethacrylate) (PMMA) has been widely used in the fields of optical instruments, aviation and auto industry, construction industry, advertising and decoration industry due to its optical transparency, low cost, low toxicity, and less fragile property. Recently it has been exploited to fabricate microfluidic chips. Region-selective metallization of PMMA surfaces are frequently required to improve the surface properties of PMMA and to integrate micro metal devices in PMMA microfluidic chips. This article presents our recent study on region-selective metalization of PMMA by means of UV/O-3-based surface modification in combination of region-selective electroless plating. Deep UV-lights, ozone, and deep UV-lights in cooperation with ozone were compared with respect to the efficiency of hydrophilization of the PMMA surface. It was observed with water contact angle measurements that only synchronized deep UV and ozone treatment can turn the PMMA surface from hydrophobic to hydrophilic effectively. Attenuated total reflection fourier transform infrared spectra revealed that polar moieties such as carboxyl groups were generated on the UV/O-3 treated areas. These polar moieties served as the anchors for further chemical reactions including amination of the carboxyl groups with ethylenediamine, adsorption of chloraurate anion onto the amine groups, and reduction of the Au(III) in the chloraurate anion to Au(0) by borohydride. These reactions led to the formation of the catalysis center of gold nano-particles on the UV-irradiated areas, which is indispensable for region-selective electroless plating. After optimization of the experimental conditions, a novel method for preparation of micro metal devices on PMMA surface has been established. With the printed poly(ethylene terephthalate) (PET) film serving as the primary photo mask, the achievable resolution of the prepared micro metal patterns was 50 mu m or less. The deposited metal films adhered to the PMMA surface so strongly that they could hardly be tore off with adhesive tapes. Micro gold electrodes, micro gold electric heaters, micro copper electrodes, etc. were demonstrated to be prepared on PMMA surfaces, and their physical and electro-chemical properties were characterized.

Surface Modification with Special Morphology for the Metallization of Polyimide Film

Copper Metallization on the Surface-Modified Polyimide Films by Electroless Plating Method

Photocatalytic Surface Modification of PI Film for Electroless Copper Plating

Plasma Treatment and Surface Analysis of Polyimide Films for Electroless Copper Buildup Process

Grafting Amino Groups onto Polyimide Films in Flexible Copper-Clad Laminates Using Helicon Plasma

Localized Surface Hydrophilicity Tailoring of Polyimide Film for Flexible Electronics Manufacturing Using an Atmospheric Pressure Ar/H2O Microplasma Jet

Preparation of Highly Reflective and Conductive Metallized Polyimide Films Through Surface Modification: Processing, Morphology and Properties

Direct additive copper plating on polyimide surface with silver ammonia via plasma modification

Effect of surface roughness on the adhesion properties of Cu/Cr films on polyimide substrate treated by inductively coupled oxygen plasma

Region-selective Metalization of Poly(methylmethacrylate) Surface Based on UV/ozone Surface Modification

Imprinting Of Metal Receptors Into Multilayer Polyelectrolyte Films: Fabrication And Applications In Marine Antifouling

Polyion Multi Layers with Precise Surface Charge Control for Antifouling

Super-high interface adhesion through silver/polyimide heterojunction

Modification of Cu Nanoparticles with A Disulfide for Polyimide Metallization

Mechanism analysis of PI/PEEK interface bonding properties enhanced by atmospheric plasma treatment: Experiment and DFT calculation

Modifying wetting properties of PI Film: The impact of surface texturing and CF 4 and O 2 plasma treatment

Plasma surface pretreatment to improve interfacial adhesion strengths of sputtered Cu on polyimide film

Preparation of MoS2@PDA-Modified Polyimide Films with High Mechanical Performance and Improved Electrical Insulation

Surface Modification of Polyether Ether Ketone Thin Films Through Ion Implantation

Chemically Modified Graphene/polyimide Composite Films Based on Utilization of Covalent Bonding and Oriented Distribution.

Surface Modification of Polyethylene Separator for Li-Ion Batteries via Imine Formation