Abstract:Lead zirconate titanate and polydimethylsiloxane (PZT–PDMS) thin films are an attractive choice for a flexible piezoelectric substrate. In this work, the surface modification of the PZT–PDMS composite with plasma treatment is developed to fabricate flexible conductor patterns or devices directly on the composite surface. Optimized plasma treatment conditions are achieved by varying plasma parameters such as the pressure of treatment, type of gas, gas flow, and time of treatment. Plasma polymerization is carried out using C2H4–CO2, and argon (Ar) is used for the surface ablation effect in low-pressure conditions. Atmospheric pressure plasma (APP) is performed in a N2 atmosphere which has a surface etching effect. All the treatments create a hydrophilic layer, which is confirmed with water contact angle measurements, X-ray photoelectron spectroscopy, and Fourier transform infrared analysis. Silver conductive ink was printed on the plasma-treated films to fabricate flexible conductive patterns, and the bonding strength was tested by performing adhesive tests such as tape, ultrasonic, and soak tests. APP treatment under a N2 environment with a 300 V input voltage, 21.5 kHz frequency, and 2 min deposition time proves to be the most efficient surface modification technique. This treatment produces a silica-like layer on the composite surface and results in better wettability. It reduces the contact angle from 108 to 20° immediately after the treatment and shows strong adhesion during several rigorous adhesion tests. The printed conductive patterns on the N2-treated film show strong mechanical stability and exhibit great electric conductivity under bending and releasing. The APP treatment under N2 environment can overcome the adhesion issue of the printed conductive layer on the hydrophobic composite surfaces. Moreover, all the above plasma treatments have a negligible effect on the piezoelectric properties of PZT–PDMS films.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsapm.0c01117.Low-pressure, capacitively coupled RF plasma reactor used for surface treatment of PZT–PDMS films, schematic drawing of the atmospheric pressure DBD plasma reactor used for surface treatment of the PZT–PDMS films, original images of XPS analysis and elemental quantification of untreated and treated films, and contact angles measured after 48 h of treatment (PDF)Measurement of the charge response of piezoelectric PZT–PDMS films (MP4)This article has not yet been cited by other publications.

Modifying wetting properties of PI Film: The impact of surface texturing and CF 4 and O 2 plasma treatment

Localized Surface Hydrophilicity Tailoring of Polyimide Film for Flexible Electronics Manufacturing Using an Atmospheric Pressure Ar/H2O Microplasma Jet

Surface immobilization of polymer brushes onto porous poly(vinylidene fluoride) membrane by electron beam to improve the hydrophilicity and fouling resistance

Mechanism analysis of PI/PEEK interface bonding properties enhanced by atmospheric plasma treatment: Experiment and DFT calculation

Plasma Mode Influences on the Surface Hydrophobization of Polyimide

Surface Modification of Polymeric Materials by Plasma Immersion Ion Implantation

Controlling the triboelectric properties and tribological behavior of polyimide materials via plasma treatment

Surface Modification of Poly(tetrafluoroethylene) Films Via Plasma Treatment and Graft Copolymerization of Acrylic Acid

Force-Based Characterization of the Wetting Properties of LDPE Surfaces Treated with CF4 and H2 Plasmas

Plasma Treatment of Composite Piezoelectric Thin Films for Good Adhesion of Printed Conductive Ink

Plasma Treatment and Surface Analysis of Polyimide Films for Electroless Copper Buildup Process

Preparation and Characterization of Anisotropic Chain Structures in Polyimide Films

Hydrophilic modification of a polyimide film surface

Effect of surface roughness on the adhesion properties of Cu/Cr films on polyimide substrate treated by inductively coupled oxygen plasma

Enhanced Wettability and Adhesive Property of PTFE through Surface Modification with Fluorinated Compounds

Effect of amine and acid functionalization on polyimide: A structure-property relationship study

Effects of argon plasma treatment on carbon fiber surface characteric and its reinforcing polyimide composites interfacial properties at room and elevated temperatures

Enhanced Mechanical and Thermal Properties of Polyimide Films Using Hydrophobic Fumed Silica Fillers

Plasma-Modified PI Substrate for Highly Reliable Laser-Sintered Copper Films Using Cu2O Nanoparticles

Plasma surface pretreatment to improve interfacial adhesion strengths of sputtered Cu on polyimide film

Enhanced Wetting and Adhesive Properties by Atmospheric Pressure Plasma Surface Treatment Methods and Investigation Processes on the Influencing Parameters on HIPS Polymer