Abstract:In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either explicitly in mechanical models or implicitly in empirical relationships. Furthermore, there are cases where the connection between various concrete elements explicitly depends on dowel action, as for example, in connections between precast elements or between two concrete parts cast at different times. On the other side, dowel action can have a negative impact on the fatigue resistance of reinforcing bars subjected to cyclic loading, because of the local stress concentrations near interfaces due to relative movements, either in sliding or in opening of cracks not perpendicular to the bar. For the assessment of the remaining capacity of existing structures, improved models of the behavior are needed, including realistic models of the behavior of concrete, steel and their interfaces. The aim of the present paper is to provide a contribution to a better understanding of dowel action by two test series. The first series focused on the behavior of the dowel: the concrete specimens with the embedded bars were placed in a custom‐made test setup and subjected to monotonic or low stress‐level cyclic actions with a longitudinal and a transversal crack opening component, up to developing the full plastic capacity of the dowel and rupture at the peak of catenary action. The measurement system included tracking the displacement field at the surface of the concrete and the strains in the dowel by optical fibers glued on its surface. The latter measurements allow to derive the internal forces in the reinforcing bar and deformed shape of the bar as well as the contact pressure between the bar and the surrounding concrete. The results show a strong dependency on the test variables: diameter of the bar, imposed crack kinematics and angle between the bar and the crack. The second test series looked more closely at the behavior of concrete underneath the bar, in the presence of a point load introduced at various locations into concrete through a reinforcing bar. A comparison of the test results with existing models shows a general good agreement and some aspects that deserve to be improved.

Screw Reinforcement on Dowel-Type Moment-Resisting Connections with Cracks

INCORPORATING PRE-EXISTING CRACKS IN STRUCTURAL ASSESSMENT OF RC STRUCTURES

Crack Propagation And Fracture Process Zone (Fpz) Of Wood In The Longitudinal Direction Determined Using Digital Image Correlation (Dic) Technique

Densified wood dowel reinforcement of timber perpendicular to the grain: a pilot study

Experimental Research on Dowelled Connection of GluBam-Concrete Composite Beams

Connections Used for Cold-Formed Steel Frame Shear Walls Sheathed with Engineered Bamboo Panels

Strengthening of Composite T-joints Using Ø 0.11 Mm Z-pins Via an Ultrasound-Guided Insertion Process

Cracking Behavior of Cfrp Laminate-Strengthened Rc Beams with Premechanical and Postmechanical Environmental Damage

In-plane testing and hysteretic modeling of steel-spline cross-laminated timber diaphragm connection with self-tapping screws

Study on Surface Cracking of Corroded Reinforced Concrete Based on DIC Method

Experimental and numerical analysis of tensile properties in steel-timber bonded-screwed hybrid single-lap joints with different drilling directions

Experimental and Numerical Studies on the Traditional Penetration Mortise–Tenon Connection Reinforced by Self-Tapping Screws

Strengthening Single-Bolt Timber Joints with Externally Bonded CFRP Composites

Numerical and Experimental Analysis of the Load-Carrying Capacity of a Timber Semi-Rigid Dowel-Type Connection

CRACK MODEL OF REINFORCED CONCRETE BASED ON STRAIN DECOMPOSITION METHOD

Experimental investigation of dowel action in reinforcing bars using refined measurements

Axial load-deformation behavior and fracture characteristics of bolted steel to laminated timber and glubam connections

Rotational Stiffness and Carrying Capacity of Timber Frame Corners with Dowel Type Connections

Three-Dimensional Bond Model Considering the Coupled Damage Effect for Dowel Action

Reinforcement for earthquake-damaged glued-laminated timber knee-braced frames with self-tapping screws and CFRP fabric

Three-dimensional numerical analyses of load-bearing behavior and failure of multiple double-shear dowel-type connections in timber engineering