Abstract:Sheet metals usually exhibit a certain degree of plastic anisotropy because of the rolling effect. To characterize the anisotropic behavior in simulations related to large deformation, strain-rate independent phenomenological models are frequently used in quasi-static conditions. Two functions are generally included in such a model, i.e. the yield function and the plastic potential. The former limits the stress state within the yield surface while the latter determines the direction of the plastic strain increment. Traditional plasticity models mostly assume associated flow rule, in which the two functions mentioned above are identical. With the enhanced demand of accuracy, the forms of the associated models become too complex with more and more parameters to achieve an easy calibration procedure. Alternatively, in the past decade the non-associated models were increasingly used for sheet metals. Separate functions for the two aspects of plasticity lead to efficient characterization and convenient calibration. In numerical study of dynamic loading cases, how to characterize strain-rate dependence of plasticity is an important issue. Some visco-plastic models were developed to take the rate effect into account, e.g. Johnson-Cook and Cowper-Symonds models, where the isotropic J2 flow theory was commonly used. However, when the material is severely anisotropic, this approach is very likely to be insufficient, and a model including both anisotropy and rate dependence would be needed. Extending a non-associated anisotropic model to be rate-dependent is a promising approach which has not been published in open literature to the best knowledge of the authors. Objective of the present study is to develop an applicable model for characterizing dynamic mechanical behavior of a typical high-strength steel sheet. Two steps are performed. The material is investigated under quasi-static loading firstly. Tensile test results show an obvious anisotropy which cannot be described by traditional associated models. So the non-associated Hill48 model is chosen and calibrated. Accuracy of the model is verified by a quasi-static punching test. Thereafter the dynamic material properties are obtained by conducting tensile tests at quite a few strain-rate levels covering 0.0004–1200s−1. To characterize the positive strain-rate effect in strength, the non-associated Hill48 model is extended to be visco-plastic after checking two rate-dependence formulations in existing isotropic models. With implementing the extended model into a user subroutine of ABAQUS/explicit, simulations of the dynamic tension tests are run and compared to the real experiments. A good agreement between the simulated and the experimental result is achieved using the VUMAT.

Determining the Coefficients of a Homogeneous Anisotropic Hardening Model for Ultrathin Steel Sheets

Springback after the Lateral Bending of T-Section Rails of Work-Hardening Materials

Finite element modeling for analyzing the production of high-strength steel sheets for automobile parts

An application of fully coupled ductile damage model considering induced anisotropies on springback prediction of advanced high strength steel materials

Characterization of kinematic and distortional hardening by cyclic twin-bridge shear tests for sheet metal with inverse engineering approach

Analysis of springback for multiple bending considering nonlinear unloading-reloading behavior, stress inheritance and Bauschinger effect

Investigation into Springback Characteristics of Two Hss Sheets During Cold V-Bending

Material Modeling of Hot-Rolled Steel Sheet Considering Differential Hardening and Hole Expansion Simulation

Extension of Non-Associated Hill48 Model for Characterizing Dynamic Mechanical Behavior of A Typical High-Strength Steel Sheet

An analytical model for bending and springback of bimetallic sheets

Development of a new model for plane strain bending and springback analysis

Improving the Accuracy of Stamping Analyses Including Springback Deformations

Modeling Techniques for Strain-Range-Dependent Hardening Behavior of Low-Yield-Point Steel Shear Panel Dampers

User-friendly anisotropic hardening function with non-associated flow rule under the proportional loadings for BCC and FCC metals

Analytical and Numerical Prediction of Springback of SS/Al-Alloy Cladded Sheet in V-Bending

Effect of Different Yield Criteria and Material Parameter Identification Methods on the Description Accuracy of the Anisotropic Behavior of 5182-O Aluminum Alloy

Application of distortional plasticity framework to EDDQ and TRIP steel sheets: Prediction of latent hardening and its influence on springback

Characterisation and modelling of anisotropic hardening behaviour of cubic and hexagonal close packed polycrystalline metals

A Generally Anisotropic Hardening Model for Big Offset-Strain Yield Stresses

Description of elastic–plastic stress–strain transition in cyclic plasticity and its effect on springback prediction

Effects of Hardening Model and Variation of Elastic Modulus on Springback Prediction in Roll Forming