Abstract:Selective laser sintering (SLS) combined with reaction melt infiltration was used to fabricate Si–SiC ceramic matrix composites, and the effects of different concentrations of phenolic resin (PF) on the properties of the SLS green body and carbonized and final Si–SiC samples were investigated. The results showed that the impregnation with PF can increase the bulk density, reduce the porosity of the samples at all stages, and improve the mechanical properties of the reactive bonded samples. The degree of densification and mechanical properties of the sample gradually enhanced with an increase in PF concentration. The main phases of the Si–SiC composites were free Si, α-SiC, β-SiC, plus an extremely small amount of Al–Si alloy, and the SiC and the Si phase contents increased and decreased, respectively, as the concentration of PF increased when measured using Rietveld refinement and image analysis software. The macroscopic properties of the samples improved greatly after precursor infiltration pyrolysis (PIP) treatment with 66.7%vol PF-ethanol solution twice. According to the crystal nucleation-growth theory, it was inferred that the infiltrated PF could provide a certain amount of pyrolytic carbon in the carbonized specimen. During the reaction bonded process, the carbon formed by carbonization pyrolysis first dissolves into the molten Si and reaches saturation. With the further dissolution of carbon, [C] and [Si] in the liquid phase contact each other to form β-SiC nuclei, the nuclei that precipitate at the pore wall position and gradually form a continuous interfacial layer of β-SiC. The β-SiC layer prevents the liquid Si from direct contact with C inside the prefabricated body, therefore, further reactants diffuse through the layer. Finally, the fine crystalline β-SiC grains were fabricated inside the specimen.

Effect of Silicon Addition on the Microstructure, Mechanical and Thermal Properties of Cf/SiC Composite Prepared Via Selective Laser Sintering

Effects of chopped carbon fiber on the forming, structure and mechanical properties of CCF/SiC composites fabricated by SLS and RMI

Effects of carbon content on microstructure and mechanical properties of SiC ceramics fabricated by SLS/RMI composite process

Additive manufacturing of Csf/SiC composites with high fiber content by direct ink writing and liquid silicon infiltration

Fabrication and characterization of carbon fiber reinforced SiC ceramic matrix composites based on 3D printing technology

Microstructure and Mechanical Properties of Unidirectional, Laminated Cf/SiC Composites with α-Al2O3 Nanoparticles as Filler

Microstructure and mechanical properties of short-carbon-fiber/Ti3SiC2 composites

Fabrication and characterization of SiC/Al composites prepared by laser powder bed fusion (LPBF) combined with vacuum pressure infiltration

A novel porous carbon synthesized to serve in the preparation of highly dense and high-strength SiC/SiC by reactive melt infiltration

Effect of impregnated phenolic resin on the properties of Si–SiC ceramic matrix composites fabricated by SLS-RMI

Additive manufacturing of continuous carbon fiber-reinforced silicon carbide composite by fused filament fabrication and precursor infiltration pyrolysis

Microstructure and Mechanical Properties of Cf/SiC Composites with Dispersed C-SiC Interphase Prepared by Chemical Vapor Infiltration

Enhancing mechanical properties of selectively laser sintered SiC/Si composites printed using electrostatic spraying microspheres with fine particles

Preceramic Paper-Derived SiCf/SiCp Composites Obtained by Spark Plasma Sintering: Processing, Microstructure and Mechanical Properties

Fabrication of C/SiC composites by siliconizing carbon fiber reinforced nanoporous carbon matrix preforms and their properties

Influence of Silicon Addition on the Sintering Behavior and Mechanical Properties of Boron Carbide by SPS Process

Effect of mass transfer channels on flexural strength of C/SiC composites fabricated by femtosecond laser assisted CVI method with optimized laser power

Effect of laser parameters on microstructure and phase evolution of Ti-Si-C composites prepared by selective laser melting

Influence of micron and nano SiCp on microstructure evolution and mechanical properties of laser metal deposition AlSi10Mg alloy

Influence of Sintering Process on the Fracture Behavior of C-F/SiC Laminated Ceramic Composites

Fabrication of dense Cf/SiC ceramic matrix composites using 3D printing and PIP with short carbon fibre as a toughening material