Abstract:Large aluminum alloy ring forgings are the core components of heavy-duty rocket fuel storage tanks, and the large residual stress inside the rings leads to poor shape accuracy of large thin-walled parts. The initial stress of the 2219 aluminum alloy ring blank was tested using the drilling method, and the creep constitutive coefficient of the 2219 aluminum alloy was determined through stress relaxation tests. The numerical simulation processes of thermal stress relief (TSR), vibration stress relief (VSR), and thermal–vibration stress relief (TVSR) were compared and established. Through the correlation analysis between the actual measurement results of residual stress and the simulation results, it can be seen that the strong correlation in three directions at each measurement point accounts for over 37.5%, and the moderate correlation accounts for over 62.5%. This indicates that the numerical simulation model of 2219 aluminum alloy ring containing initial residual stress can accurately reflect the size and distribution of residual stress inside the actual ring. The simulation results show that the derived constitutive model can describe the stress relaxation process of TVSR by combining a single thermal time effect stress relaxation constitutive theory with a VSR plastic deformation material model. The simulation models established above were used to calculate the residual stress homogenization ability of three types of aging. The results showed that VSR, TSR, and TVSR can homogenize and reduce the residual stress field inside the ring, improve the distribution of residual stress inside the ring, and have a better overall homogenization ability of TVSR. The VSR control has a certain effect on reducing and homogenizing residual stress, but compared with TSR and TVSR, the reduction and homogenization ability of residual stress control is limited. The homogenization control effect TVSR > TSR > VSR, and the maximum equivalent stress homogenization rates of VSR, TSR, and TVSR are 52.8%, 80.6%, and 82.2%, respectively. Then, numerical simulation technology was used to study how the initial residual stress in the blank causes the deformation of the ring during the thin-walled machining process. The roundness error theory of the minimum containment area method was applied to evaluate the deformation degree during the thin-walled numerical machining process, and the TVSR method was used for stress regulation. The deformation law of the thin-walled machining of the ring under different aging parameters was studied.

Analysis and Homogenization of Residual Stress in Aerospace Ring Rolling Process of 2219 Aluminum Alloy Using Thermal Stress Relief Method

Numerical Simulation and Experiment of Stress Relief and Processing Deformation of 2219 Aluminum Alloy Ring

Evolution of Residual Stress Based on Curvature Coupling in Multi-Roll Levelling

Finite Element Method Simulation for Residual Stress in Quenched Aluminum Alloy Thick-Plate and Its Effect on Machining Distortion

Research on machining deformation of aluminum alloy rolled ring induced by residual stress

Multi-objective optimization of parametric design for profile ring rolling process based on residual stress control

Finite Element Simulation Analysis on Residual Stress Relief of 7075 Aluminum Alloy Ring

Research on process optimization and rapid prediction method of thermal vibration stress relief for 2219 aluminum alloy rings

Residual stresses evolution and process route optimization of TC4 profiled rolled rings incorporating thermal bulging

Analysis and Simulation of Machining Deformation Resulting from Residual Stress

Numerical simulation of stress evolutions in 2A14 aluminum alloy components during solution and aging process

Investigation on the Evolution of Residual Stress in Ultrasonic Surface Rolling Treatment-Processed 18CrNiMo7-6 Alloy Steel

Multi-scale Simulation of Recrystallization during Rolling of Large 2219 Aluminum Alloy Rings

The Residual Stress and Deformation Control of TC4 Thin-Walled Outer Ring Components by Ultrasonic Regulation

Effect of coarse second-phase particles on mechanical properties of large-scale 2219 Al alloy rings

The central strain analytical modeling and analysis for the plate rolling process

Influence of Gradual Stress Relieving on the Microstructure, Texture Development, Grain Structure and Orientation of the Hot-Rolled Ti6Al4V-5Cu Alloy.

Residual stress relaxation considering microstructure evolution in heat treatment of metallic thin-walled part

Multi-response optimization of the bulging-processed parameters for enhanced residual stress state of TC4-rolled rings

Numerical Simulation of Quenching-Stretching Process of Aluminum Alloy Plate and Analysis of Mechanism of Reducing Residual Stresses

Numerical and Experimental Research on Cold Compression Deformation Method for Reducing Quenching Residual Stress of 7A85 Aluminum Alloy Thick Block Forging