Abstract:Large aluminum alloy ring forgings are the core components of heavy-duty rocket fuel storage tanks, and the large residual stress inside the rings leads to poor shape accuracy of large thin-walled parts. The initial stress of the 2219 aluminum alloy ring blank was tested using the drilling method, and the creep constitutive coefficient of the 2219 aluminum alloy was determined through stress relaxation tests. The numerical simulation processes of thermal stress relief (TSR), vibration stress relief (VSR), and thermal–vibration stress relief (TVSR) were compared and established. Through the correlation analysis between the actual measurement results of residual stress and the simulation results, it can be seen that the strong correlation in three directions at each measurement point accounts for over 37.5%, and the moderate correlation accounts for over 62.5%. This indicates that the numerical simulation model of 2219 aluminum alloy ring containing initial residual stress can accurately reflect the size and distribution of residual stress inside the actual ring. The simulation results show that the derived constitutive model can describe the stress relaxation process of TVSR by combining a single thermal time effect stress relaxation constitutive theory with a VSR plastic deformation material model. The simulation models established above were used to calculate the residual stress homogenization ability of three types of aging. The results showed that VSR, TSR, and TVSR can homogenize and reduce the residual stress field inside the ring, improve the distribution of residual stress inside the ring, and have a better overall homogenization ability of TVSR. The VSR control has a certain effect on reducing and homogenizing residual stress, but compared with TSR and TVSR, the reduction and homogenization ability of residual stress control is limited. The homogenization control effect TVSR > TSR > VSR, and the maximum equivalent stress homogenization rates of VSR, TSR, and TVSR are 52.8%, 80.6%, and 82.2%, respectively. Then, numerical simulation technology was used to study how the initial residual stress in the blank causes the deformation of the ring during the thin-walled machining process. The roundness error theory of the minimum containment area method was applied to evaluate the deformation degree during the thin-walled numerical machining process, and the TVSR method was used for stress regulation. The deformation law of the thin-walled machining of the ring under different aging parameters was studied.

Multi-objective optimization of parametric design for profile ring rolling process based on residual stress control

Multi-response optimization of the bulging-processed parameters for enhanced residual stress state of TC4-rolled rings

Residual stresses evolution and process route optimization of TC4 profiled rolled rings incorporating thermal bulging

Numerical Simulation and Experiment of Stress Relief and Processing Deformation of 2219 Aluminum Alloy Ring

An innovative spinning-rolling process and its intelligent FE modelling for big-tapered profiled ring disk

Multi-objective optimization of cavity design for GH4738 superalloy profile ring rolling process based on FEM and RSM

Parameter optimization in hot precision forging process of synchronizer ring based on grey relational analysis and response surface method

Optimization of Forging Process Parameters and Prediction Model of Residual Stress of Ti-6Al-4V Alloy

Multi-objective optimization of concave radial forging process parameters based on response surface methodology and genetic algorithm

Evaluation Methods and Coupled Optimization at Macro- and Micro-Scales for Profiled Ring Rolling of Inconel718 Alloy

Research on machining deformation of aluminum alloy rolled ring induced by residual stress

Forming process chain for manufacturing complex conical-section profiled rings: On a co-design method

A 6-Sigma Robust Optimization Method for Stamping Forming of Automobile Covering Parts Based on Residual Error and Radial Basis Interpolation

Study on Residual Stress Produced in Milling of Aeronautic Structure

Numerical Analysis and Parameter Optimization of Wear Characteristics of Titanium Alloy Cross Wedge Rolling Die

Finite element analysis and response surface method for robust multi-performance optimization of radial turning of hard 300M steel

Modeling and optimization of surface residual stress profiles in milling of aluminum 7075-T6 alloy

Machining-induced residual stress analysis and multi-objective optimization for milling process of Mg–Li alloy

Multiobjective Optimization of Experimental and Simulated Residual Stresses in Turning of Nickel-Alloy IN100

Buckling Defect Optimization of Constrained Ring Rolling of Thin-Walled Conical Rings with Inner High Ribs Combining Response Surface Method with FEM

Multi-Objective Process Parameter Optimization of Ultrasonic Rolling Combining Machine Learning and Non-Dominated Sorting Genetic Algorithm-II