Abstract:Large aluminum alloy ring forgings are the core components of heavy-duty rocket fuel storage tanks, and the large residual stress inside the rings leads to poor shape accuracy of large thin-walled parts. The initial stress of the 2219 aluminum alloy ring blank was tested using the drilling method, and the creep constitutive coefficient of the 2219 aluminum alloy was determined through stress relaxation tests. The numerical simulation processes of thermal stress relief (TSR), vibration stress relief (VSR), and thermal–vibration stress relief (TVSR) were compared and established. Through the correlation analysis between the actual measurement results of residual stress and the simulation results, it can be seen that the strong correlation in three directions at each measurement point accounts for over 37.5%, and the moderate correlation accounts for over 62.5%. This indicates that the numerical simulation model of 2219 aluminum alloy ring containing initial residual stress can accurately reflect the size and distribution of residual stress inside the actual ring. The simulation results show that the derived constitutive model can describe the stress relaxation process of TVSR by combining a single thermal time effect stress relaxation constitutive theory with a VSR plastic deformation material model. The simulation models established above were used to calculate the residual stress homogenization ability of three types of aging. The results showed that VSR, TSR, and TVSR can homogenize and reduce the residual stress field inside the ring, improve the distribution of residual stress inside the ring, and have a better overall homogenization ability of TVSR. The VSR control has a certain effect on reducing and homogenizing residual stress, but compared with TSR and TVSR, the reduction and homogenization ability of residual stress control is limited. The homogenization control effect TVSR > TSR > VSR, and the maximum equivalent stress homogenization rates of VSR, TSR, and TVSR are 52.8%, 80.6%, and 82.2%, respectively. Then, numerical simulation technology was used to study how the initial residual stress in the blank causes the deformation of the ring during the thin-walled machining process. The roundness error theory of the minimum containment area method was applied to evaluate the deformation degree during the thin-walled numerical machining process, and the TVSR method was used for stress regulation. The deformation law of the thin-walled machining of the ring under different aging parameters was studied.

Effect of coarse second-phase particles on mechanical properties of large-scale 2219 Al alloy rings

Multi-scale Simulation of Recrystallization during Rolling of Large 2219 Aluminum Alloy Rings

Preparation of Millimeter Scale Second Phase Particles in Aluminum Alloys and Determination of Their Mechanical Properties

Effect of Fibrous Macrostructure on Mechanical Properties, Anisotropy and Fracture Mechanism of Roller Bearing Ring

Numerical Simulation and Experiment of Stress Relief and Processing Deformation of 2219 Aluminum Alloy Ring

Second phase strengthening mechanism of 2219 aluminum alloy

Evolution of the Second-Phase Particles and Their Effect on Tensile Fracture Behavior of 2219 Al-xCu Alloys

Research on machining deformation of aluminum alloy rolled ring induced by residual stress

Forming process chain for manufacturing complex conical-section profiled rings: On a co-design method

Effect Of Coupled Annular Electromagnetic Stirring And Intercooling On The Microstructures Macrosegregation And Properties Of Large-Sized 2219 Aluminum Alloy Billets

Optimization of numerical parameters and microstructure evolution on 2195 Al–Li alloy extrusion process

An inclusive comparative study on the influences of the ring rolling process at elevated temperatures on the mechanical properties and microstructures of two centrifugally cast light alloys

Macrostructure, microstructure and mechanical properties evolution during 8Cr4Mo4V steel roller bearing inner ring forging process

Research on the Morphology and Size Development of Al-Mg-Si-Cu Particle during Mechanical Alloying

Research on plastic deformation transfer and distribution of large-diameter thin-walled metal ring parts in double-roll pendulum hot rotary forging process

The Influences of Multiscale Second-Phase Particles on Strength and Ductility of Cast Mg Alloys

Effect of forging pretreatment on the microstructures and mechanical properties of the Al-Cu-Li alloy

Microstructure evolution and mechanical anisotropy of M50 steel ball bearing rings during multi-stage hot forging

Fe-bearing phase formation, microstructure evolution, and mechanical properties of Al-Mg-Si-Fe alloy fabricated by the twin-roll casting process

Microstructure and Wear Properties of Al-Based Bearing Alloys Fabricated by Mechanical Alloying

Mechanical Property Research of Different Materials for Supporting Rings