Abstract:In this study, we conducted an extensive analysis and research of the microstructure, mechanical features, and fracture behaviors of Al–8Si– x Mg alloy sheets under natural aging. The results reveal that while the dimensions of GP zones remained relatively unchanged with increasing Mg concentrations, their volume fraction progressively increased before reaching a plateau. It was observed that at a Mg concentration of 1.32%, numerous particles clustered areas comprising Mg 2 Si and Si particles were discovered. With the increase of Mg concentration in the alloy sheets, there was an initial uptick in strength, followed by a minor decline thereafter. Concurrently, the elongation consistently exhibited a reduction. The yield strength of Al–8Si alloy sheets under natural aging, incorporating varying Mg content levels, was precisely predicted. Moreover, the predicted value demonstrated strong agreement with the actual data obtained. Additionally, this research illuminated the impact of diverse strengthening mechanisms on the yield strength. Under tensile stress, the experimental alloy sheets exhibited a ductile fracture mechanism. Initially, as the Mg concentration increased, the quantity of dimples on the fracture surface remained steady, then slightly increased, while the depth of these dimples progressively became shallower and their size slightly decreased. Additionally, a rise in Mg content led to a smoother texture on the alloy sheets' surface after undergoing tensile fracture. Secondary fractures reduced in quantity, and some secondary cracks bypassed the Si particles. Moreover, the quantity of cracked Si particles gradually grew.

Microstructure and Fracture Behavior of Al‐Si‐Mg Alloy Prepared with Recycled Alloy

Ductility Fracture Mechanisms of Al-7Si-Mg Casting Alloys Considering Si Particles: A Combined Experimental and Crystal Plasticity Study

Low cycle fatigue response and fracture mechanism in a novel Al-3.5Si-0.5Mg-0.4Cu casting alloy

On the characterization of microstructure and fracture in a high-pressure die-casting Al-10 <i>wt</i>%Si alloy

Effect of microstructural evolution on mechanical properties and fracture modes of AlSi10Mg blocks fabricated by selective laser melting after stress relief annealing

Study on hot deformation behavior and dynamic recrystallization mechanism of recycled Al–Zn–Mg–Cu alloy

Cracking Behavior, Microstructure and Properties of Selective Laser Melted Al-Mn-Mg-Sc-Zr Alloy

Modification of Iron-Rich Phase in Al-7Si-3Fe Alloy by Mechanical Vibration during Solidification

Study on Microstructure, Mechanical Properties and Erosion Characteristics of Al-Si Alloy Manufactured by Continuous Casting Direct Rolling Process

Microstructure and mechanical properties of Al−Mg−Si alloy U-shaped profile

Modeling Microstructure and Yield Strength during Solidification and Heat Treatment Process in Al-7Si-Mg Cast Aluminum Alloys

Fatigue and Fracture Behavior of AlSi10Mg Manufactured by Selective Laser Melting: A Review

Effect of Initial Fe Content on Microstructure and Mechanical Properties of Recycled Al-7.0Si-Fe-Mn Alloys with Constant Mn/Fe Ratio

Microstructure and mechanical properties of AZ31B magnesium alloy prepared by solid-state recycling process from chips

Tensile properties and fracture behavior of Al–8Si alloy sheets with different Mg under natural aging

New Technologies of Aluminum Castings. Effect of Microstructure on Fracture Toughness of Cast and Forged Aluminum Casting Alloys.

The influence of AlSi10Mg recycled powder on corrosion-resistance behaviour of additively manufactured components: mechanical aspects and acoustic emission investigation

Microstructure evolution of recycled 7075 aluminum alloy and its mechanical and corrosion properties

Fracture Behavior of a High Pressure Die Casting AlSi10MnMg Alloy with Varied Porosity Levels

Ductile and Corrosion-Resistant Aluminum Alloy From Recycled Secondary Aluminum Scraps Containing Iron Impurities

Effect of Processing Route on Microstructure and Mechanical Properties of an Al-12Si Alloy