Abstract:Refractory metal carbides TiC, ZrC, HfC, NbC and TaC have excellent physical, chemical and mechanical properties as materials for ultra-high temperature ceramics. Of these, the most refractory are TaC and HfC, whose melting points approach 4000°C. It should be noted the high hardness, strength and wear resistance of refractory carbides. Hence, there is a natural interest in high-entropy carbides based on them, which are becoming an important class of new ceramic materials, since they potentially have more advanced applied properties. However, obtaining such materials by classical metallurgical methods is a difficult task. In modern research, samples of high-entropy carbides are most often synthesized using expensive special equipment (methods of plasma-spark sintering, high-energy planetary mills, etc.) and a relatively long preparation of precursors for sample production. This paper describes a new approach to the synthesis of multicomponent carbide (Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2)C using an electrochemical process at a temperature not exceeding 1173 K. The method is based on the phenomenon of currentless metal transfer in molten salts. After the step-by-step transfer of metals, the sample was washed from the electrolyte, then sintered in a vacuum furnace. According to X-ray phase analysis, the resulting high-entropy carbide is a single-phase solid solution with an FCC structure. The diffraction pattern of the synthesized sample is in good agreement with the calculated diffraction pattern obtained by the Debye formula for a supercell of 64 000 atoms. A compact sample of high-entropy carbide was produced by pressing a tablet 10 mm in diameter with the addition of cobalt as a matrix metal. After vacuum sintering, the sample was ground to prepare for examination on a scanning electron microscope. Elemental mapping of the sample surface was performed, which showed a satisfactory distribution of metals that make up the high-entropy carbide. The measured microhardness of the sample turned out to be less than the values found in the publications of other authors, which may be due to some residual sample porosity.

High Entropy Carbide Ceramics from Different Starting Materials

Microstructures and mechanical properties of (Nb0.25Mo0.25Ta0.25W0.25)C and (Nb0.2Mo0.2Ta0.2W0.2Hf0.2)C high-entropy carbide ceramics produced by arc melting

Structure evolutions of the polymer derived medium-/high-entropy metal carbides

Microstructure, Mechanical and Tribological Properties of High-Entropy Carbide (MoNbTaTiV)C5

Microstructures and mechanical properties of high-entropy (Ti0.2Zr0.2Hf0.2Nb0.2Ta0.2)C ceramics with the addition of SiC secondary phase

From stoichiometric to non-stoichiometric high-entropy carbide: a case study of hafnium addition

A practical guideline for designing high-entropy carbides based on (Ti1/3Mo1/3W1/3)C with high valence electron concentration

Processing and Properties of High-Entropy Ultra-High Temperature Carbides

High-entropy carbide-nitrides with enhanced toughness and sinterability

High-entropy carbide ceramics with refined microstructure and enhanced thermal conductivity by the addition of graphite

Preparation and mechanical properties of (Ti0.2Zr0.2V0.2Nb0.2Ta0.2)(C0.6N0.4)-Co high-entropy cermets

Host Lattice and Solid Solution Formation in an Octal-Cation (NbTaZrTiHfVWMo)C High Entropy Carbide Ceramic

Novel Synthesis of (hf 0.25 Zr 0.25 Ti 0.25 Ta 0.25 )C-Sic Biphasic Ceramic Micro-Powders Using Single-Source-precursor Route

Fabrication and Characterization of Polymer‐derived High‐entropy Carbide Ceramic Powders

The effect of submicron grain size on thermal stability and mechanical properties of high‐entropy carbide ceramics

Equiatomic 9-cation high-entropy carbide ceramics of the IVB, VB, and VIB groups and thermodynamic analysis of the sintering process

Grain coalescence in (Ti 0.2 Zr 0.2 Hf 0.2 Nb 0.2 Ta 0.2 )C during spark plasma sintering

Hardness of single phase high entropy carbide ceramics with different compositions

Novel Synthesis of (Hf0.25zr0.25ti0.25ta0.25)c-Sic Biphasic Ceramic Micro-Powders Using Single-Source-precursor Route

PRODUCING METHOD OF HIGH ENTROPY CARBIDE IN AN IONIC MELT

Effect of carbon content on the microstructure and mechanical properties of high-entropy (Ti0.2Zr0.2Nb0.2Ta0.2Mo0.2)Cx ceramics