Abstract:Background There is a quest of novel functional and reliable platforms for enhancing the efficiency of microextraction approaches in troublesome matrices, such as industrial wastewaters. 3D printing has been proven superb in the analytical field to act as the springboard of microscale extraction approaches. Results In this work, low-force stereolithography (SL) was exploited for 3D printing and prototyping bespoke fluidic devices for accommodating nonsupported microelectromembrane extraction (μEME). The analytical performance of 3D-printed μEME devices with distinct cross-sections, including square, circle, and obround, and various channel dimensions was explored against that of commonly used circular polytetrafluoroethylene (PTFE) tubing in flow injection systems. A computer-controlled millifluidic system was harnessed for the (i) automatic liquid-handling of minute volumes of donor, acceptor, and organic phases at the low μL level that spanned from 3 to 44 μL in this work, (ii) formation of three-phase μEME, (iii) in-line extraction, (iv) flow-through optical detection of the acceptor phase, and (v) solvent removal and regeneration of the μEME device and fluidic lines. Using methylene blue (MB) as a model analyte, experimental results evinced that the 3D-printed channels with an obround cross-section (2.5 mm × 2.5 mm) were the most efficient in terms of absolute extraction recovery (59%), as compared to PTFE tubing of 2.5 mm inner diameter (27%). This is attributed to the distinctive convex interface of the organic phase (1-octanol), with a more pronounced laminar pattern, in 3D-printed SL methacrylate-based fluidic channels against that of PTFE tubing on account of the enhanced octanol wettability and lower contact angles for the 3D-printed devices. The devices with obround channels were leveraged for the automatic μEME and in-line clean-up of MB in high matrix textile dyeing wastewater samples with relative recoveries ≥81%, RSD% ≤ 17.1% and LOD of 1.3 μg/mL. The 3D-printed nonsupported μEME device was proven superb for the analyses of wastewater samples with an elevated ionic strength (0.7 mol L −1 NaCl, 5000 mg L −1 Na 2 CO 3 , and 0.013 mol L −1 NaOH) with recorded electric currents below 12 μA. Novelty The coupling of 3D printing with nonsupported μEME in automatic flow-based systems is herein proposed for the first time and demonstrated for the clean-up of troublesome samples, such as wastewaters.

Extraction of In3+ and Fe3+ from Sulfate Solutions by Using a 3D-Printed "Y"-Shaped Microreactor

Design and Evaluation of a Microrectification Platform Using 3D Printing

Using an Interdigital Micromixer for Separation of In3+ from Zinc Hydrometallurgical Process with D2EHPA As an Extractant

Green Effectively Enhanced Extraction to Produce Yttrium(III) in Slug Flow Microreactor

Application of three dimensional-printed devices in extraction technologies

Solvent extraction with a three-dimensional reticulated hollow-strut SiC foam microchannel reactor

Liquid–Liquid Extraction of Yttrium(III) Using 2-Ethylhexyl Phosphonic Acid Mono-2-ethylhexyl (EHEHPA) in a Microreactor: A Comparative Study

3D-printed stereolithographic fluidic devices for automatic nonsupported microelectromembrane extraction and clean-up of wastewater samples

TiO2 nanoparticle-Coated 3D-Printed porous monoliths enabling highly sensitive speciation of inorganic Cr, As, and Se

Extraction and Separation of Metal Ions by a Column Packed with Polystyrene Microcapsules Containing Aliquat 336

3D-printed thermally expanded monolithic foam for solid-phase extraction of multiple trace metals

Application of Microchemical Technology in Mass Transfer Behavior Contrastive Research of Rare Earth Extraction

Extraction of Fe3+ from NaH2PO4 Solution in a Spiral Microchannel Device

Continuous Extraction of Gold(III) Using Pyridine Ionic Liquid-Based Water-in-Oil Microemulsion in Microreactors

Extraction of Samarium Using a Serpentine Y-junction Microreactor with 2-Ethylhexyl Phosphonic Acid Mono-2-ethylhexyl

Solvent extraction of Ac-225 in nano-layer coated, solvent resistant PDMS microfluidic chips

Gas-liquid-liquid extraction in a novel rotating microchannel extractor

Ultrathin Hydrophobic Inorganic Membranes Via Femtosecond Laser Engraving for Efficient and Stable Extraction in a Microseparator

Continuous-Flow Catalytic Degradation of Hexacyanoferrate Ion through Electron Transfer Induction in a 3D-Printed Flow Reactor

Solvent Extraction of Rare Earth Metals by Microchannel Extractor

Embedded 3D Printing for Microchannel Fabrication in Epoxy-Based Microfluidic Devices