Abstract:Microextraction coupled to mass spectrometry (MS) has great potential in analytical chemistry laboratories operating in a variety of fields. Indeed, microextraction methods directly coupled to MS can be of large value given that they can provide not only analyte extraction and enrichment but also effective sample cleanup. In recent years, the practicality in handling high active surface area, versatility, and environmentally friendly features of magnetic dispersive microextraction technologies has contributed to an explosion in the number of methods and technologies reported in the literature for a wide range of applications. However, to the best of our knowledge, no technology to date has been capable of efficiently merging these two rising concepts in a simple and integrated analytical workflow. In this context, the microfluidic open interface is presented for the direct coupling of dispersive magnetic extraction to mass spectrometry. This technology operates under the concept of a flow-isolated desorption volume, which generates a stagnant droplet open to ambient conditions while continuously feeding the ionization source with solvent by means of the self-aspiration process intrinsic of the electrospray ionization (ESI) interface. To improve the efficiency of the final analytical workflow, a novel dispersive magnetic micro- and nanoparticle extraction protocol for biofluid droplets was developed. The final methodology entailed the dispersion of a small amount of magnetic particles (20-70 μg) in a droplet of biofluid (≤40 μL) for extraction, followed by a particle collection step using a homemade 3D-printed holder containing an embedded rare-earth magnet. In the final step, the holder is set on top of the microfluidic open interface (MOI) for desorption in the isolated droplet. Switching the valve transfers the desorbed analytes to the ESI source in less than 5 s. As proof of concept, the completely new setup was applied to the determination of prohibited substances from phosphate-buffered saline (PBS) and human urine using Fe2O3 magnetic nanoparticles (50 nm) functionalized with C18. The limits of quantitation (LOQs) obtained were in the low-ppb range in all cases, and acceptable precision (≤20%) and accuracy (80-120%) were attained. Also, taking advantage of the fast extraction kinetics provided by the radial diffusion associated with small particles, we employed the methodology for the selective extraction of phosphopeptides from 40 μL of tryptic β-casein digest using 70 μg of magnetic Ti-IMAC microparticles. To conclude, the technology and methodology herein presented provided excellent capabilities comparable to those of other solid-phase microextraction (SPME-MS) approaches while dramatically minimizing the amount of sample and sorbent required per analysis, as well as affording significantly fast extraction times due to the enhanced kinetics of extraction.

Enhancing the Concentration Capability of Nonsupported Electrically Driven Liquid-Phase Microextraction through Programmable Flow Using an All-In-One 3D-Printed Optosensor: A Proof of Concept

Optical Micro/nanofibre Embedded Soft Film Enables Multifunctional Flow Sensing in Microfluidic Chips

3D-printed stereolithographic fluidic devices for automatic nonsupported microelectromembrane extraction and clean-up of wastewater samples

Non-Invasive Manipulation of Two-Phase Liquid-Liquid Slug Flow Parameters Using Magnetofluidics

3-D printed microfluidics for rapid prototyping and testing of electrochemical, aptamer-based sensor devices under flow conditions

Direct Coupling of Dispersive Extractions with Magnetic Particles to Mass Spectrometry via Microfluidic Open Interface

On-chip drop-to-drop liquid microextraction coupled with real-time concentration monitoring technique

An Electrodiffusion Model Coupled with Fluid-Flow Effects for an On-Chip Electromembrane Extraction System

Projection Micro-Stereolithography to Manufacture a Biocompatible Micro-Optofluidic Device for Cell Concentration Monitoring

Microfluidic Flow-through SPME Chip for Online Separation and MS Detection of Multiple Analyses in Complex Matrix

A Custom 3D Printed Permeate Probe Device for Enhanced Membrane Monitoring and Characterization

3D-Printed Microfluidic Device with In-line Amperometric Detection that Also Enables Multi-Modal Detection

Ion-Induced Phase Transfer of Cationic Dyes for Fluorescence-Based Electrolyte Sensing in Droplet Microfluidics

Fabricating And Characterizing The Microfluidic Solid Phase Extraction Module Coupling With Integrated Esi Emitters

A 3D-Printed Micro-Optofluidic Chamber for Fluid Characterization and Microparticle Velocity Detection

Application of a Micro Free-Flow Electrophoresis 3D Printed Lab-on-a-Chip for Micro-Nanoparticles Analysis

Electrically Controllable Microparticle Synthesis and Digital Microfluidic Manipulation by Electric-Field-Induced Droplet Dispensing into Immiscible Fluids

Fabrication of Low-Cost, High-Resolution Open Capillary Microfluidics towards Self-Sustaining, Long-Term Hydration of Engineered Living Materials

A 3D printed sheath flow interface for surface enhanced Raman spectroscopy (SERS) detection in flow

One step multi-material 3D printing for the fabrication of a photometric detector flow cell

Automated Membrane Characterization: In-situ Monitoring of the Permeate and Retentate Solutions using a 3D Printed Permeate Probe Device