Abstract:Background There is a quest of novel functional and reliable platforms for enhancing the efficiency of microextraction approaches in troublesome matrices, such as industrial wastewaters. 3D printing has been proven superb in the analytical field to act as the springboard of microscale extraction approaches. Results In this work, low-force stereolithography (SL) was exploited for 3D printing and prototyping bespoke fluidic devices for accommodating nonsupported microelectromembrane extraction (μEME). The analytical performance of 3D-printed μEME devices with distinct cross-sections, including square, circle, and obround, and various channel dimensions was explored against that of commonly used circular polytetrafluoroethylene (PTFE) tubing in flow injection systems. A computer-controlled millifluidic system was harnessed for the (i) automatic liquid-handling of minute volumes of donor, acceptor, and organic phases at the low μL level that spanned from 3 to 44 μL in this work, (ii) formation of three-phase μEME, (iii) in-line extraction, (iv) flow-through optical detection of the acceptor phase, and (v) solvent removal and regeneration of the μEME device and fluidic lines. Using methylene blue (MB) as a model analyte, experimental results evinced that the 3D-printed channels with an obround cross-section (2.5 mm × 2.5 mm) were the most efficient in terms of absolute extraction recovery (59%), as compared to PTFE tubing of 2.5 mm inner diameter (27%). This is attributed to the distinctive convex interface of the organic phase (1-octanol), with a more pronounced laminar pattern, in 3D-printed SL methacrylate-based fluidic channels against that of PTFE tubing on account of the enhanced octanol wettability and lower contact angles for the 3D-printed devices. The devices with obround channels were leveraged for the automatic μEME and in-line clean-up of MB in high matrix textile dyeing wastewater samples with relative recoveries ≥81%, RSD% ≤ 17.1% and LOD of 1.3 μg/mL. The 3D-printed nonsupported μEME device was proven superb for the analyses of wastewater samples with an elevated ionic strength (0.7 mol L −1 NaCl, 5000 mg L −1 Na 2 CO 3 , and 0.013 mol L −1 NaOH) with recorded electric currents below 12 μA. Novelty The coupling of 3D printing with nonsupported μEME in automatic flow-based systems is herein proposed for the first time and demonstrated for the clean-up of troublesome samples, such as wastewaters.

Fabrication of Plastic Micro-Channels for Microfluidics Solvent Extraction

Simple and Cost-Effective Fabrication of Two-Dimensional Plastic Nanochannels from Silica Nanowire Templates

Micro Etching Method Inside Microchannels

Fabrication of full glass chips with hybrid micro- and nanochannels and their application to protein concentration

Fabrication of microchannels by space-selective control of phase separation in glass.

Bonding-Free Capillary Microfluidics via a 3D-Printed Railed Microchannel

An Alternative Micro-Milling Fabrication Process for Rapid and Low-Cost Microfluidics

A novel abrasive water jet machining technique for rapid fabrication of three-dimensional microfluidic components

Fabrication of Topologically Complex Three-Dimensional Microfluidic Systems in PDMS by Rapid Prototyping

Fabrication of Microfluidic Manifold by Precision Extrusion Deposition and Replica Molding for Cell-Laden Device

Controllable Preparation of Microscale Tubes with Multiphase Co-Laminar Flow in a Double Co-Axial Microdevice

Composite Elastomer-Enabled Rapid Photofabrication of Microfluidic Devices

Fabrication of Perfluoropolyether Microfluidic Devices Using Laser Engraving for Uniform Droplet Production

Digital light processing 3D printing of microfluidic devices targeting high-pressure liquid-phase separations

3D printed metal molds for hot embossing plastic microfluidic devices

3D-printed stereolithographic fluidic devices for automatic nonsupported microelectromembrane extraction and clean-up of wastewater samples

Rapid Micromolding of Sub-100 µm Microfluidic Channels Using an 8K Stereolithographic Resin 3D Printer

Polymer Microfluidics: Simple, Low-Cost Fabrication Process Bridging Academic Lab Research to Commercialized Production

Fabrication and Performance of Poly(methyl Methacrylate) Microfluidic Chips with Fiber Cores.

Microplastic separation and enrichment in microchannels under derivative electric field gradient by bipolar electrode reactions

A Novel Hollow-Fiber Membrane Embedded Co-axial Microdevice for Simultaneous Extraction and Stripping