Abstract:Interfacial engineering is critical for highly efficient charge carrier transport in perovskite solar cells (PSCs). Herein, we developed a new method, called successive surface engineering, that affords PSCs with enhanced efficiency and dramatically suppressed current-voltage hysteresis. Upon modifying the TiO2 compact layer, which is commonly used as an electron transport layer (ETL) in regular-structure (n-i-p) planar heterojunction (PHJ) PSCs, by successively incorporating [6,6]-phenyl-C-61-butyric acid methyl ester (PC61BM) and an ethanolamine (ETA)-functionalized fullerene (C-60-ETA) synthesized facilely via a one-pot nucleophilic addition reaction, the average power conversion efficiency (PCE) of the CH3NH3PbI3-based PHJ-PSC devices increased from 13.00% to 16.31%; the best PCE attained was 18.49%, which, to our knowledge, represents the highest PCE reported to date for regular-structure PHJ-PSCs devices based on fullerene-modified TiO2 interlayers. In contrast, single surface engineering of the TiO2 layer with a PC61BM or C-60-ETA layer alone results in only negligible changes in PCE, revealing the synergistic effect of these two fullerene derivatives: the PC61BM layer can passivate the traps on the TiO2 surface, while the subsequent C-60-ETA layer not only improves the wettability of the perovskite film on the ETL but also facilitates electron transport across the interface between the perovskite and the TiO2 ETL. The structural and morphological characterizations show that following dual surface modification of the TiO2 layer with PC61BM and C-60-ETA, both the surface coverage and crystallinity of the CH3NH3PbI3 perovskite film are improved. Steady-state photoluminescence decay and electrochemical impedance spectroscopic studies manifest that the dual surface modification substantially improves the charge extraction efficiency and suppresses charge recombination. As a consequence, this dual surface modification leads to an obvious increase of the short-circuit current density (J(sc)), which contributes primarily to the PCE enhancement. Additionally, because PC61BM may induce passivation of the traps on the TiO2 surface and in the perovskite layer, remarkably, the hysteresis of the current-voltage response is dramatically suppressed following the dual surface modification.

Solution-processed electron transport layer of n-doped fullerene for efficient and stable all carbon based perovskite solar cells

A Facile Interface Engineering Method to Improve the Performance of FTO/ZnO/CsPbI 3− X Br X ( X < 1)/C Solar Cells

Enhancing Efficiency and Stability of Inverted Perovskite Solar Cells through Solution‐Processed and Structurally Ordered Fullerene

Pyridine‐functionalized Fullerene Derivative As an Independent Electron Transport Layer Enabling Efficient and Hysteresis‐free Regular Perovskite Solar Cells

A ternary organic electron transport layer for efficient and photostable perovskite solar cells under full spectrum illumination

Boosting fill factor and open-circuit voltage of carbon-based perovskite solar cells with graphene co-doped P3HT/NiOx hole-transporting bilayer

Vertical Phase Separated Cesium Fluoride Doping Organic Electron Transport Layer: A Facile and Efficient “bridge” Linked Heterojunction for Perovskite Solar Cells

Efficient, stable, and fully printed carbon-electrode perovskite solar cells enabled by hole-transporting bilayers

A Solution-Processed Dopant-Free Tin Phthalocyanine (snpc) Hole Transport Layer for Efficient and Stable Carbon-Based CsPbI2Br Planar Perovskite Solar Cells Prepared by a Low-Temperature Process

Highly Stable and Efficient Perovskite Solar Cells with 22.0% Efficiency Based on Inorganic–Organic Dopant‐Free Double Hole Transporting Layers

Cross‐Linkable Fullerene Electron Transport Layer with Internal Encapsulation Capability for Efficient and Stable Inverted Perovskite Solar Cells

Fabrication, characterization and simulation analysis of perovskite solar cells with dopant-free solution-processible C6PcH2 hole transporting material

Efficient Carbon-Based CsPbBr3 Inorganic Perovskite Solar Cells by Using Cu-Phthalocyanine as Hole Transport Material

Fullerene Polymer Complex Inducing Dipole Electric Field for Stable Perovskite Solar Cells

Ultra-large dipole moment organic cations derived 3D/2D p–n heterojunction for high-efficiency carbon-based perovskite solar cells

High-performance, Stable and Low-Cost Mesoscopic Perovskite (ch3nh3pbi3) Solar Cells Based on Poly(3-Hexylthiophene)-modified Carbon Nanotube Cathodes

Methods and strategies for achieving high-performance carbon-based perovskite solar cells without hole transport materials

Successive Surface Engineering Of Tio2 Compact Layers Via Dual Modification Of Fullerene Derivatives Affording Hysteresis-Suppressed High-Performance Perovskite Solar Cells

Contact Engineering and In‐Situ Formation of 2D Perovskite via Solid‐Phase Growth for Efficient Hole‐Transport‐Layer‐Free Perovskite Solar Cells

Dithieno[3,2‐b:2′,3′‐d]pyrrol‐Cored Hole Transport Material Enabling Over 21% Efficiency Dopant‐Free Perovskite Solar Cells

Comparative Study on TiO 2 and C 60 Electron Transport Layers for Efficient Perovskite Solar Cells