Abstract:<p>Due to the intrinsic high room temperature brittleness and cold-cracking susceptibility, the fabrication and forming of γ-TiAl intermetallic alloy component is extremely difficult. Therefore, in recent years, a wire-arc additive manufacturing (WAAM) technique has been developed to fabricate the γ-TiAl intermetallic alloy by depositing the Ti and Al wires into a single tungsten arc generated molten pool with specific wire feed ratios. However, the WAAM fabricated γ-TiAl intermetallic alloy has been found having inhomogeneous layer-by-layer microstructure and the excessive heat input of tungsten arc would induce significant residual stress in the bulk sample. In the present paper, the previous WAAM has been further upgraded and an innovative twin-wire plasma arc additive manufacturing (TW-PAAM) process has been developed. Afterwards, a γ-TiAl intermetallic alloy wall component with specific chemical composition of Ti-48Al has been fabricated and the metallography, phase composition and tensile properties are characterized subsequently. It has been found that a significantly more uniform microstructure is obtained in the TW-PAAM fabricated γ-TiAl intermetallic alloy than the previous WAAM technique. The content of α<sub>2</sub> phase, lamellar colony size and lamellar spacing exhibited the tendency of decreasing from the lower to upper part along building direction. And the tensile strength and ductility of the lower section are lower than the middle and top sections. In general, the present TW-PAAM technique has shown promising capability of fabricating γ-TiAl intermetallic alloy with lower cost, and the investigation results would become a valuable reference for understanding the evolution mechanism of microstructure and mechanical properties of the additively manufactured TiAl alloy.</p>

Microstructure and Mechanical Properties of TiB2/ Al-Si Composites Fabricated by TIG Wire and Arc Additive Manufacturing

Microstructure and Mechanical Properties of TiB2/AlSi7Mg0.6 Composites Fabricated by Wire and Arc Additive Manufacturing Based on Cold Metal Transfer (WAAM-CMT)

Microstructure and Mechanical Properties of TiB2/Al-Si Composites Fabricated by Electron Beam Rapid Manufacture

Microstructure and mechanical properties of Al-Cu alloy during wire and arc additive manufacturing by adding micron TiB2 particles

Heat Accumulation, Microstructure Evolution, and Stress Distribution of Ti–Al Alloy Manufactured by Twin‐Wire Plasma Arc Additive

Effect of Heat Treatment on Microstructure and Tensile Properties of Ti-6Al-4V Alloy Produced by Coaxial Electron Beam Wire Feeding Additive Manufacturing

Microstructure and mechanical properties of Ti-3Al-2V alloy by dual wire + arc additive manufacturing

Microstructure and Mechanical Properties of AlSi7Mg0.6 Aluminum Alloy Fabricated by Wire and Arc Additive Manufacturing Based on Cold Metal Transfer (WAAM-CMT)

Microstructure and mechanical properties of an in-situ TiB2 particle reinforced AlSi10Mg composite additive manufactured by selective electron beam melting

Wire arc additive manufacturing of the Al-5.55Cu alloy: Insight the effect of intrinsic heat treatment on microstructure and mechanical properties

Microstructural and mechanical properties of wire-arc additively manufactured Al–Zn–Mg aluminum alloy: The comparison of as-deposited and heat-treated samples

Fabrication of γ-TiAl intermetallic alloy using the twin-wire plasma arc additive manufacturing process: Microstructure evolution and mechanical properties

Microstructure and Fatigue Properties of Ti-48Al Alloy Fabricated by the Twin-Wire Plasma Arc Additive Manufacturing

Microstructure and mechanical properties of wire arc additively manufactured 205A high strength aluminum alloy: The comparison of as-deposited and T6 heat-treated samples

Microstructure and Mechanical Properties of Al-Cu-Mg Alloy Fabricated by Double-Wire CMT Arc Additive Manufacturing

Research on Technology of 7075 Aluminum Alloy Processed by Variable Polarity TIG Additive Manufacturing Utilizing Nanoparticle-Reinforced Welding Wire with TiB2

Effect of Heat Treatment Processes on the Microstructure and Mechanical Properties of High-Strength Aluminum Alloy Deposited Layers Processed by Fused Arc Additive Manufacturing

In-situ ternary wire + arc additive manufacturing thin-walled Ti-Ni-Cu-Al-V component: Microstructure and mechanical properties

Improvement of microstructure and mechanical properties of CMT wire arc additive manufacturing Al-Si alloy deposition via interlayer coating TiC nanoparticles

Microstructure, Corrosion and Mechanical Properties of TiC Particles/Al-5Mg Composite Fillers for Tungsten Arc Welding of 5083 Aluminum Alloy

Promoting Strengthening and Grain Refinement of Aluminum Alloy During Wire and Arc Additive Manufacturing by Adding TiB2 Particles