Abstract:In this paper, a fine particle matter (PM) sensor has been designed, built up, and measured. It consists of a LED, a photodiode, a glass air channel and collimated structure, as show in Fig.1. Compared with the conventional fine PM sensors [1-2], this sensor has higher sensitivity and better reliability via immunity to particle contamination. A simulation model of the particle matter sensor is built based on the right angle Mie-scattering theory [3]. The simulation results are shown in Fig 2. In the simulation, the wavelength of LED is 650 nm, and particles diameter is 1 μm. The particles are guided into a “U” shape glass channel with a good light transparence at visible light region. And the light is collimated by an embedded lens in LED packaging, and injected into the glass channel with the minimum scattering from the glass channel. The particles are isolated by the glass channel so that they cannot contaminate the LED and the photodiode, which is a common failure mode in conventional PM sensors. Based on the simulation and fitting process, the detection limitation is down to around 0.2 μg/m3 when the power of the light source is 0.4mW and specific detectivity of the photodiode is 0.017uW. The sensor used in characterization is assembled as shown in Fig. 3. A TSI 9306 six-jet atomizer is used to generate fine particles (diameter ~ 1 m) carried by dry-air gas flow. A reference PM detector (model: TSI 8520 DustTrak Aerosol Monitor) is connected at the outlet of the sensor to monitor the particle mass concentration in real-time. The glass channel with gold coating is used to guide the particle air. The experimental results are shown in Fig. 4. The blue dots and red line are the testing and fitting results, respectively. Through analysis, the relationship between particle mass concentration and PD voltage can match to linear trend. The output signal is up to approximate 1.5 μV when the PM concentration changes 1μg/m3, and the detection limitation is around 3.3ug/m3, which is much better than the value of 10μg/m3 of the conventional PM sensors.

An Aerosol Sensor for PM1 Concentration Detection Based on 3D Printed Virtual Impactor and SAW Sensor

System Integration of an Optimally Designed Virtual Impactor with a QCM Sensor As a One-Stop PM2.5 Classification and Detection Platform

A Miniature System for Separation and Detection of PM Based on 3-D Printed Virtual Impactor and QCM Sensor

A Miniature System for Classification and Concentration Detection of PM Based on 3D Printed Virtual Impactor and QCM Sensor

High-performance Virtual Sensors Array Based on a Single-chip FBAR for Volatile Organic Compounds (vocs) Detection and Classification

Airborne Particulate Matter Classification and Concentration Detection Based on 3D Printed Virtual Impactor and Quartz Crystal Microbalance Sensor

A Simple Optical Aerosol Sensing Method of Sauter Mean Diameter for Particulate Matter Monitoring

Online Aerosol pH Detection Using 3D-Printed Microfluidic Devices with a Novel Magnetic SERS Sensor

Silicon Microfabrication Based Particulate Matter Sensor

Sub-Micro Particle Matter Detection for Metal 3-D Printing Workshop

A Miniature Aerosol Sensor for Detecting Polydisperse Airborne Ultrafine Particles

Real-time detection of molecular structures and metal components within airborne particles using concurrent Raman and Spark emission spectroscopy

Detection of Particulate Matter of Size 2.5 μm with a Surface-Acoustic-Wave Sensor Combined with a Cyclone Separator

A New Particle Sensor Based on True RMS Value Measurement.

A Micro Aerosol Sensor for the Measurement of Airborne Ultrafine Particles

Method Research for Determination of PM2.5 Concentration with a New Developed Vibration Sensor

Dissecting PM sensor capabilities: A combined experimental and theoretical study on particle sizing and physicochemical properties

A system of continuous particles monitoring using virtual impactor

<strong>Demonstration of a highly sensitive fine particle matter sensor</strong>

A PCB Type Aerosol Sensor for Measuring Nanoscale Aerosol Particles

Fundamentals of low-cost aerosol sensor design and operation