Abstract:Cd alloying pure sulfide kesterite solar cells by regulating the alloying concentration and the grain growth process systematically from Sn4+‐DMSO solution approach makes a large‐grain spanning absorber monolayer and significantly suppresses deep‐level defects. At the optimal concentration, a champion device with an efficiency of 12.3% is achieved with a record low open‐circuit voltage loss even without post heat treatment. Cd alloying has been theoretically proved to be an effective strategy to suppress Cu‐Zn antisite defects and related defect cluster for improving device performance of pure sulfide kesterite Cu2ZnSnS4 (CZTS) thin film solar cells. However, the potential of Cd alloying has not been fully realized by solely doping without further post heat‐treatment. Here, Cd alloying CZTS (Cu2(Zn,Cd)SnS4, CZCTS) is reported through dimethyl sulfoxide (DMSO) solution and how alloying concentration affects reaction path, grain growth, and electronic properties of the CZCTS absorbers is investigated. This study found that Cd can be incorporated into CZTS through direct phase transformation grain growth, which sufficiently suppresses band tailing. High quality CZCTS absorber films and efficient solar cells are fabricated within a wide range of alloy concentration. A champion CZCTS device with a power conversion efficiency of 12.3% is achieved at 35% Cd concentration without any post heat treatment, improved by over 70% compared to 7.0% of CZTS. This device exhibits a high VOC gain to the Shockley–Queisser (Voc/VocSQ = 59.7%), the lowest VOC deficit achieved in pure sulfide kesterite solar cells. The results demonstrate the importance of the Cd alloying strategy for mitigating band tailing and achieving high efficiency pure sulfide kesterite solar cells.

Understanding the Effect of Cadmium Alloying in High-Efficiency Sulphide Kesterite Cu2ZnxCd1-xSnS4 Solar Cell by PDS and HRSTEM

Formation of Alloyed Cu2CoxZn1-xSn(S,Se)4 Absorption Layer and Its Application in Solar Cells.

Formation of Alloyed Cu2Cox Zn1-x Sn(S,Se)4 Absorption Layer and Its Application in Solar Cells

12.3% Efficient Low Voc Loss Pure Sulfide Kesterite Solar Cells from DMSO Solution via Cadmium Alloying

Strategy for Performance Enhancement of Cd1-XZnXTe/CdS Core/shell Quantum Dot Sensitized Solar Cells Through Band Adjustment

Beyond 11% Efficient Cu2ZnSn(Se,S)(4) Thin Film Solar Cells by Cadmium Alloying

Synergetic Effects of Zn Alloying and Defect Engineering on Improving the CdS Buffer Layer of Cu2ZnSnS4 Solar Cells

Enhancement of the photovoltaic performance of Cd-alloyed Cu2ZnSn(S,Se)4 films based on a low-cost water-based solution process

Doping Behavior of Zn in CdS and Its Effect on the Power Conversion Efficiency of the Cu2ZnSn(S, Se)4 Solar Cell

Improvement of Power Conversion Efficiency of Cu <sub>2</sub>znsn(s,se) <sub>4</sub> Solar Cells by Al Doped CdS

From Atomic Structure to Photovoltaic Properties in CdTe Solar Cells

Effects of CuAlO2 on the heterojunction interface and performance of Cu2ZnSn(S,Se)4 thin-film solar cells

Exploring New Cadmium Salts to Enhance the Photovoltaic Conversion Efficiency of Cu 2 ZnSn(S,Se) 4 Solar Cells

Structural, Electronic and Defect Properties of Cu 2 ZnSn(S,Se) 4 Alloys

Origin of Band-Tail and Deep-Donor States in Cu2ZnSnS4 Solar Cells and Their Suppression Through Sn-Poor Composition

Multinary alloying for facilitated cation exchange and suppressed defect formation in kesterite solar cells with above 14% certified efficiency

Structural, Electronic and Defect Properties of Cu<sub>2</sub>ZnSn(S,Se)<sub>4</sub> Alloys

Over 10% Efficiency Pure Sulfide Kesterite Solar Cells on Transparent Electrode with Cd-Ag Co-Alloying

Optimizing the properties of Cu2ZnSn(S,Se)4 solar cells via cationic substitution with trace Ca

Crystal Structure and Defect Reactions in the Kesterite Solar Cell Absorber Cu[sub 2]znsns[sub 4] (CZTS): Theoretical Insights

First-principles insights into the electronic structure, optical and band alignment properties of earth-abundant Cu2SrSnS4 solar absorber