Abstract:The non-coaxial stacked holes caused by cutting deformation is a common problem in stack drilling, particularly for low-rigidity structure, and the non-coaxiality in carbon-fibre-reinforced plastic and aluminium (CFRP/Al) stack drilling has not been studied. Because of the non-homogeneous behaviour and poor machinability of CFRP, the non-coaxiality in CFRP/Al stack drilling is significantly different from previous studies on Al/Al stack drilling. Focusing on the non-coaxiality in CFRP/Al stack drilling, this paper proposed the mechanism of the non-coaxiality through both experiments and numerical study. Severe non-coaxiality occurrences were observed in the CFRP/Al stack drilling experiments. To explain the observation, the macroscopic mechanics theory of composite was applied to obtain the engineering constants of composite laminates, which are necessary for the numerical model. This application leads to the development of an optimized simulation model to predict the interlayer gaps and non-coaxiality. The numerical results that predict the non-coaxiality are consistent with the experiments, which verified the rationality of simulation model. Furthermore, the effect of the thrust force and clamping force on both interlayer gaps and non-coaxiality were studied. The interlayer gaps gradually increase with the increase in thrust force but decrease with the clamping force. Moreover, the thrust force has a complicated effect on the non-coaxiality. The non-coaxiality first decreases and subsequently increases with the increase in thrust force, which can be attributed to the "tilt effect" in the lower layer. In addition, the non-coaxiality increases with the clamping force in the simulation experiment range. The work in this paper enables us to understand the particularity of the non-coaxiality in CFRP/Al stack drilling and select the appropriate cutting parameters for CFRP/Al stack drilling.

Influence of Cooling/lubrication Conditions on the Drilling Quality and Thrust Force of CFRP/Al Stacks

Hole Diameter Variation and Roundness in Dry Orbital Drilling of Cfrp/Ti Stacks

A Theoretical Model for Predicting the CFRP Drilling-Countersinking Thrust Force of Stacks

Processing research on orbital drilling of CFRP/Ti-6Al-4V stacks

Experimental investigation on drilling machinability and hole quality of CFRP/Ti6Al4V stacks under different cooling conditions

Investigation Of Minimum Quantity Lubrication Effects In Drilling Cfrp/Ti6al4v Stacks

On the Analysis of Temperatures, Surface Morphologies and Tool Wear in Drilling CFRP/Ti6Al4V Stacks under Different Cutting Sequence Strategies

Comparative Study of Minimum Quantity Lubrication and Dry Drilling of CFRP/titanium Stacks Using TiAlN and Diamond Coated Drills

Experimental Investigation on Drilling of PTFE/CFRP/Aluminum Stack

Drilling Temperature and Hole Quality in Drilling of CFRP/aluminum Stacks Using Diamond Coated Drill

Experimental Study on Mechanical Drilling of Carbon/epoxy Composite-Ti6al4v Stacks

Investigation of CFRP damages induced by the interface high temperature and mixed tool wear mechanism in drilling of thin-walled CFRP /Ti stacks

On the Quantitative Analysis of Drill Edge Wear when Machining CFRP/Ti6Al4V Stacks

Influence of Metal Chips on Drilling Quality of Carbon Fiber Reinforced Plastic and Titanium Stacks

! Investigation on the Non-Coaxiality in the Drilling of Carbon-Fibre-reinforced Plastic and Aluminium Stacks

Influence of main cutting edge structure on hole defects in CFRP/titanium alloy stacks drilling

Tool Wear Processes in Low Frequency Vibration Assisted Drilling of CFRP/Ti6Al4V Stacks with Forced Air-Cooling

Effect of Drilling Parameters and Tool Geometry on Drilling Performance in Drilling Carbon Fiber–reinforced Plastic/titanium Alloy Stacks

High reliability model of mechanical response in drilling of CFRP/Al stacks

Investigation of Drilling CFRP-TC4 Stacks

Effects of Different Cooling Methods on the Specific Energy Consumption when Drilling CFRP/Ti6Al4V Stacks