Abstract:Ti5Si3/TiAl composites were successfully prepared by pressure infiltration and subsequent reactive annealing. Final microstructure of Ti5Si3/TiAl composites was dependent on the reactive annealing temperature, which varied from 1350 degrees C to 1420 degrees C, two typical microstructures could be achieved: (i) An unique core-shell structure (Core: fully lamellar alpha 2-Ti3Al/gamma-TiAl with in-situ synthesized Ti5Si3 particles predominantly distributed at the interfaces of alpha 2/gamma lamellar colonies; Shell: equiaxed gamma-TiAl with Ti5Si3 particles distributed in gamma grain boundaries); And (ii) A novel quasi-network structure composed of fully lamellar alpha 2/gamma and a majority of Ti5Si3 particles with a quasi-network distribution. The formation of the two microstructures could be attributed to the chemical composition heterogeneity which was caused by the difference in interdiffusion rate of Ti and Al elements in different annealing temperatures. The comparative investigations on high temperature tensile properties and creep behavior showed that the core-shell Ti5Si3/TiAl composites exhibited a better specific strength (165 MPa center dot g- 1 center dot cm3) and higher ultimate tensile strength (633 MPa) at 800 degrees C, which was 12 % higher than that of the quasi-network Ti5Si3/TiAl composites. While the creep behavior analysis showed that in compassion with equiaxed gamma phase, the slip distance of dislocations in fully lamellar alpha 2/gamma phase was shorter, impeding the motion of dislocations more effectively. And core-shell Ti5Si3/TiAl composites possessed a large number of grain boundaries concentrating in the shell which became weaker in the high temperature, facilitating the formation of creep pores in the shell and the final premature fracture. Hence, the quasi-network Ti5Si3/TiAl composites containing a higher content of fully lamellar alpha 2/gamma exhibited a better creep resistance than that of core-shell Ti5Si3/TiAl composites. More importantly, the steady state creep rate at 750 degrees C under the fixed stress of 250 MPa of quasi-network Ti5Si3/TiAl composites was relatively low, only 3.305 x 10-8 s- 1, comparable to that of third-generation TiAl alloys.

In Situ Ti2AlN Reinforced TiAl-based Composite with a Novel Network Structure: Microstructure and Flexural Property at Elevated Temperatures

High Temperature Tensile Properties of in Situ TiBw/Ti6Al4V Composites with a Novel Network Reinforcement Architecture

Tensile Properties and Fracture Behavior of In-Situ Synthesized Ti 2 AlN/Ti48Al2Cr2Nb Composites at Room and Elevated Temperatures

Fabrication and Mechanical Properties of in Situ Synthesized Ti 2 AlN/TiAl Composite

Microstructural Characteristics and Evolution of Ti2AlN/TiAl Composites with a Network Reinforcement Architecture During Reaction Hot Pressing Process

Significant Enhancement in High Temperature Performance of TiAl Matrix Composites by a Novel Configuration Design

Microstructure and Elevated-Temperature Mechanical Properties of in Situ Ti2AlNb-reinforced TiAl-matrix Composite Prepared by Powder Metallurgy

Network-Strengthened Ti-6Al-4V/(TiC+TiB) Composites: Powder Metallurgy Processing and Enhanced Tensile Properties at Elevated Temperatures

Microstructural Characterization and Mechanical Properties of a Novel TiC-based Cermet Bonded with Ni3(Al,Ti) and NiAl Duplexalloy

Constitutive Equation and Microstructural Evolution of One Distinctive Al–based Hybrid Composite Reinforced by Nano–aln and Micro–tic Particles During Hot Compression

Fabrication of (Tib/ti)-Tial Composites with a Controlled Laminated Architecture and Enhanced Mechanical Properties

Microstructure and tensile properties of in situ synthesized (TiC + TiB + Nd2O3)/Ti-alloy composites at elevated temperature

Microstructure and Mechanical Properties of Ti2AlC Particle and In-Situ TiAl3 Reinforced Pure Al Composites

Microstructure and Mechanical Properties of Ti2AlC-reinforced TiAl Composites

Enhanced mechanical properties of a novel heat resistant Al-based composite reinforced by the combination of nano-aluminides and submicron TiN particles

High-temperature Mechanical Properties of 2024 Al Matrix Nanocomposite Reinforced by TiC Network Architecture

Microstructure evolution, mechanical properties, and strengthening mechanisms of heat-resistant Al-based composite reinforced by a combination of AlN and TiN particles

Investigation on Tribological Behavior of Ti2AlN/TiAl Composite at Room and Elevated Temperature

Effect of Spark Plasma Sintering Temperatures on Microstructure and Mechanical Properties of In-Situ (la2o3+tib)/ti2alnb Composites with a Tailored Three-Dimensional Network Architecture

Microstructure, Mechanical and Tribological Properties of TiAl-based Composites Reinforced with High Volume Fraction of Nearly Network Ti 2 AlC Particulates

Fabrication and Mechanical Properties of Ti2AlC/TiAl Composites with Co-Continuous Network Structure