Abstract:Polycrystalline Ni3Al-based superalloy with up to 70% <math>γ′</math> phase owns excellent strength at around 1100 °C. It has been successfully used as a substitute for turbine blade crown, which is one of the aircraft components working in the severest environment (i.e., sometimes nearly overheating). However, few studies concentrate on the coarsening resistance and phase thermal stability in this newly designed polycrystalline superalloy at the working temperature, hence, directional coarsening behavior of primary <math>γ′</math> <math>(γI′)</math> has remained restricted. This paper investigated directional coarsening behavior of <math>γI′</math> during aging treatment (1100 °C) after overheating at 1270 °C with furnace cooling (SFA), air cooling (SAA) and water cooling (SWA) respectively. It clearly showed that <math>γI′</math> grew into lamellar and gradually became irregular during the directional coarsening process. Moreover, its morphological combination mode was illustrated. Since parallel short lamellar <math>γI′</math> connected each other, long lamellar formed. When perpendicular long lamellar <math>γI′</math> connected each other, it became L-type or T-type, i.e., precursor of irregular <math>γI′</math>. The kinetics of directional coarsening regime of <math>γI′</math> was in line with the matrix-diffusion-controlled (MDC) theory according to the evaluation of <math>γI′</math> size. This was caused by higher migration of <math>γI′</math> interfaces than the diffusion of solute elements. It was also confirmed that driving force of directional coarsening mainly depended on the competition of elemental diffusion, lattice misfit distribution and <math>γ</math> channel distance.

Influence of Heat Treatment on Γ´ Phase and Property of a Directionally Solidified Superalloy

Influence of Heat Treatment on Microstructure and Stress Rupture Property of Nickel-base Superalloy

Effects of Heat Treatment on the Microstructure and Properties of a Cast Nickel-Based High-Cr Superalloy

Effect of Heat Treatment on the Microstructure and Fracture Behaviors of a Ni–Cr–Fe Superalloy

Temperature Effects on Deformation Substructures and Mechanisms of a Ni-based Single Crystal Superalloy

Effect of Heat Treatment on the Microstructure of Multiphase Nial-Based Alloy

Microstructure and Elevated Temperature Tensile Behaviour of Directionally Solidified Nickel Based Superalloy

Effect of Overheating Treatment on Microstructure and Stress Rupture Properties of a Nickel-Based Single-Crystal Superalloy

Directional coarsening behavior of primary γ′ phase in Ni3Al-based superalloy during aging heat treatment

Microstructure evolution of a nickel‐based powder metallurgy superalloy under different solution treatment temperatures

Atomic behavior of nickel-based single crystal superalloy during heat treatment process based on molecular dynamics

Microstructural evolution of GH4079 superalloy during hot deformation and heat treatment

Effect of Heat Treatment Temperature on Microstructure, Tensile Properties and δ-Precipitate Phase in Ni-based Superalloy

Influence of Various Heat Treatments on Microstructures and Mechanical Properties of GH4099 Superalloy Produced by Laser Powder Bed Fusion

Influence of thermal exposure on microstructural stability and tensile properties of a new Ni-base superalloy

Effects of pre-precipitation treatment temperature on the microstructure and mechanical properties of nickel-based powder superalloy

Influence of Forging and Heat Treatment on the Microstructure and Mechanical Properties of a Heavily Alloyed Ingot-Metallurgy Nickel-Based Superalloy

Temperature effect on the low cycle fatigue behavior of a directionally solidified nickel-base superalloy

Effect of Cooling Rate on the Microstructure and Mechanical Property of Nickel-Based Superalloy MAR-M247

Impact of Aging Temperature on the Performance of a Nickel-Iron-Based Superalloy

Influence Mechanism of Slow Cooling Treatment after Homogenization on Hot Deformation Behavior of a New Nickel-Based Superalloy