Abstract:The ternary polymerization strategy of incorporating different donor and acceptor units forming terpolymers as photovoltaic materials has been proven advantageous in improving power conversion efficiencies (PCEs) of polymer solar cells (PSCs). Herein, a series of low band gap nonconjugated terpolymer acceptors based on two different fused-ring electron-deficient building blocks (IDIC16 and ITIC) with adjustable photoelectric properties were developed. As the third component, ITIC building blocks with a larger π-conjugation structure, shorter solubilizing side chains, and red-shifted absorption spectrum were incorporated into an IDIC16-based nonconjugated copolymer acceptor PF1-TS4, which built up the terpolymers with two conjugated building blocks linked by flexible thioalkyl chain-thiophene segments. With the increasing ITIC content, terpolymers show gradually broadened absorption spectra and slightly down-shifted lowest unoccupied molecular orbital levels. The active layer based on terpolymer PF1-TS4-60 with a 60% ITIC unit presents more balanced hole and electron mobilities, higher photoluminescence quenching efficiency, and improved morphology compared to those based on PF1-TS4. In all-polymer solar cells (all-PSCs), PF1-TS4-60, matched with a wide band gap polymer donor PM6, achieved a similar open-circuit voltage (Voc) of 0.99 V, a dramatically increased short-circuit current density (Jsc) of 15.30 mA cm–2, and fill factor (FF) of 61.4% compared to PF1-TS4 (Voc = 0.99 V, Jsc = 11.21 mA cm–2, and FF = 55.6%). As a result, the PF1-TS4-60-based all-PSCs achieved a PCE of 9.31%, which is ∼50% higher than the PF1-TS4-based ones (6.17%). The results demonstrate a promising approach to develop high-performance nonconjugated terpolymer acceptors for efficient all-PSCs by means of ternary polymerization using two different A–D–A-structured fused-ring electron-deficient building blocks.This article has not yet been cited by other publications.

Efficient Ternary Polymer Solar Cells with Two Well‐Compatible Donors and One Ultranarrow Bandgap Nonfullerene Acceptor

Ternary Polymer Solar Cells with High Efficiency of 14.24% by Integrating Two Well‐Complementary Nonfullerene Acceptors

Ternary Nonfullerene Polymer Solar Cells with a Power Conversion Efficiency of 11.6% by Inheriting the Advantages of Binary Cells

Ternary Polymer Solar Cells Enabled Using Two Donor Polymers with Broad Absorption and Cascade LUMO Levels

High-Performance Ternary Nonfullerene Polymer Solar Cells with Both Improved Photon Harvesting and Device Stability.

Ternary Polymer Solar Cells Based-on Two Polymer Donors with Similar HOMO Levels and an Organic Acceptor with Absorption Extending to 850 Nm

Ternary Polymer Solar Cells Achieving 11.78% Efficiency with Two Fluorinated Non-Fullerene Acceptors

Mapping Nonfullerene Acceptors with a Novel Wide Bandgap Polymer for High Performance Polymer Solar Cells

Ternary Polymer Solar Cells with Low-Cost P3HT as the Second Donor by the Complementary Absorption Region from Long-Wavelength to Medium-Wavelength Regions Forming Cascaded HOMO and LUMO Energy Levels

Two Compatible Nonfullerene Acceptors with Similar Structures As Alloy for Efficient Ternary Polymer Solar Cells

Enhanced Photovoltaic Performances Via Ternary Blend Strategy Employing a Medium-Bandgap D-A Type Alternating Copolymer As the Single Donor

Highly Efficient Ternary All‐Polymer Solar Cells with Enhanced Stability

A Novel Wide‐Bandgap Polymer with Deep Ionization Potential Enables Exceeding 16% Efficiency in Ternary Nonfullerene Polymer Solar Cells

Ternary nonfullerene polymer solar cells with efficiency >13.7% by integrating the advantages of the materials and two binary cells

Efficient Non-Halogenated Solvent Processed Ternary All-Polymer Solar Cells with A Favorable Morphology Enabled by Two Well-Compatible Donors.

Ternary All-Polymer Solar Cells with Two Synergetic Donors Enable Efficiency over 14.5%

Semitransparent Ternary Nonfullerene Polymer Solar Cells Exhibiting 9.40% Efficiency and 24.6% Average Visible Transmittance

Ternary All-Polymer Solar Cells with 8.5% Power Conversion Efficiency and Excellent Thermal Stability.

Nonconjugated Terpolymer Acceptors with Two Different Fused-Ring Electron-Deficient Building Blocks for Efficient All-Polymer Solar Cells

Two Compatible Polymer Donors Enabling Ternary Organic Solar Cells with a Small Nonradiative Energy Loss and Broad Composition Tolerance

Chlorinated polymer solar cells simultaneously enhanced by fullerene and non-fullerene ternary strategies