Abstract:Photoelectrochemical water splitting (PEC) is a viable solution for addressing future environmental and energy concerns. However, due to the high cost of photoelectrodes and the limitations of sluggish kinetics, practical applications are limited. To achieve that goal, effective solutions are still needed to create low-cost photoelectrodes suited for PEC. Transistion metal sulfides (TMS) materials have a high potential for use as photoelectrodes due to their favorable and impressive properties 1 . The photoactivity of TMS is typically unlimited due to low reflection at the grain boundary. The individual atomic thin sheets with higher surface area compared to bulk materials allow for faster diffusion of photoinduced charge carriers primarily due to the less interface between their grains. Their lower interfacial contact resistance enables enhanced charge dynamics and, as a result, improved electrochemical reaction kinetics. When compared to other TMS, CdS has a direct bandgap and excellent photoactivity. However, its toxicity and photocorrosion make it unsuitable for long-term practical use. WS 2 is well-known layered transition metal sulfide that has a 2D molybdenite structure. It is non-toxic in acidic/neutral solutions that are chemically stable. It has been demonstrated to be more stable against oxidation and photo corrosion than CdS, which is extensively employed in photocatalysis 2 . However, because of the recombination of photoinduced charge carriers, pure WS 2 exhibits relatively poor photocatalytic efficiency and stability. As a result, combining WS 2 based photoactive nanomaterials with other suitable materials has helped overcome this challenge. Transistion metal sulfides with acceptable band structures for heterostructure construction with WS 2 may enable breakthroughs in photocatalytic and photo-electrochemical processes. The primary focus of this work is to construct heterostructures by combining CdS and WS 2 and to investigate their role as photoanodes of semiconductor materials in PEC water splitting. In this work, we have synthesised heterostructures using a facile solution-reaction method and Successive Ionic Layer Adsorption Reaction deposition (SILAR) technique which is intrinsically cost effective and scalable 3 . The heterostructure is characterised by XRD, SEM and TEM. We also studied the performance enhancement of this heterostructure using Linear sweep voltammetry and Electrochemical impedance spectroscopy. Pristine WS 2 and CdS showed photocurrent densities of 3 μA cm -2 and 20 μA cm -2 . However, heterostructures formation led to much improved photocurrents. Photocurrent densities of 151 μA cm -2 were observed for WS 2 /CdS heterostructures respectively at 1.23 V vs RHE. The enhanced improvement in photoelectrochemical performance in the case of the heterostructures could be due to the following factors: (a) the intimate interaction of this unique heterostructure improves adhesion and lowers the photoinduced charge transfer barrier; (b) increased light harvesting capability; and (c) improved charge dynamics of photoinduced charge carriers due to proper band alignment. The current study paves the way for further research into the creation of metal sulfide heterostructures that generate analogous photoelectrode materials. Keywords: Photoelectrochemical water splitting, metal sulfides, photoelectrodes. Figure 1

Atomically Thin Mesoporous In2O3–x/In2S3 Lateral Heterostructures Enabling Robust Broadband‐Light Photo‐Electrochemical Water Splitting

Synthesis of a Cu 2 O/Carbon Film/NiCoB‐Grpahene Oxide Heterostructure As Photocathode for Photoelectrochemical Water Splitting

Atomically thin photoanode of InSe/graphene heterostructure

Interfacial Engineering of In2O3/In2S3 Heterojunction Photoanodes for Photoelectrochemical Water Oxidation

3D Porous Pyramid Heterostructure Array Realizing Efficient Photo‐Electrochemical Performance

Freestanding Atomically-Thin Cuprous Oxide Sheets for Improved Visible-Light Photoelectrochemical Water Splitting

Fabrication of In2O3/In2S3 heterostructures for enhanced photoelectrochemical performance

Two-dimensional semiconducting Ag2X (X = S, Se) with Janus-induced built-in electric fields and moderate band edges for overall water splitting

Nonstoichiometric In–S Group Yielding Efficient Carrier Transfer Pathway in In2S3 Photoanode for Solar Water Oxidation

Ferroelectric polarization promotes a CdS/In2Se3 heterostructure for photocatalytic water splitting

Tuning the Carrier Transfer Behavior of Coaxial ZnO/ZnS/ZnIn2 S4 Nanorods with a Coherent Lattice Heterojunction Structure for Photoelectrochemical Water Oxidation

Interfacial engineering of 1D/2D heterostructured photoanode for efficient photoelectrochemical water splitting

Constructing a new 2D Janus black phosphorus/SMoSe heterostructure for spontaneous wide-spectral-responsive photocatalytic overall water splitting

Combined heterostructures between Bi2S3 nanosheets and H2-treated TiO2 nanorods for enhanced photoelectrochemical water splitting

Fabrication of Flower-Shaped Sb2S3/Fe2O3 Heterostructures for Enhanced Photoelectrochemical Performance

Enhanced Photoelectrochemical Performance in Engineered Interface 2D Metal Sulfide Heterostructures for Water Splitting

In-Sb Covalent Bonds over Sb2Se3/In2Se3 Heterojunction for Enhanced Photoelectrochemical Water Splitting

Highly efficient photocatalytic water splitting in direct Z-scheme α -In2Se3/Are van der Waals heterostructures

Construction of direct Z-scheme SnS@In2S3 core-shell heterojunction and its photoelectrochemical properties

Mesoporous Ultrathin In 2 O 3 Nanosheet Cocatalysts on a Silicon Nanowire Photoanode for Efficient Photoelectrochemical Water Splitting

Optimized the Carrier Transport Path and Separation Efficiency of 2D/2D Heterojunction in Photoelectrochemical Water Splitting