Low-temperature-processed SnO2–Cl for Efficient PbS Quantum-Dot Solar Cells Via Defect Passivation

Jahangeer Khan,Xiaokun Yang,Keke Qiao,Hui Deng,Jian Zhang,Zhiyong Liu,Waqar Ahmad,Jihong Zhang,Dengbing Li,Huan Liu,Haisheng Song,Chun Cheng,Jiang Tang

DOI: https://doi.org/10.1039/c7ta05366e

IF: 11.9

2017-01-01

Journal of Materials Chemistry A

Abstract:Efficient PbS quantum-dot solar cells were achieved through SnO2–Cl interface passivation.

What problem does this paper attempt to address?

Passivation Strategy of Reducing Both Electron and Hole Trap States for Achieving High-Efficiency PbS Quantum-Dot Solar Cells with Power Conversion Efficiency over 12%

Chao Ding,Feng Liu,Yaohong Zhang,Shuzi Hayase,Taizo Masuda,Ruixiang Wang,Yong Zhou,Yingfang Yao,Zhigang Zou,Qing Shen

DOI: https://doi.org/10.1021/acsenergylett.0c01561

IF: 22

2020-09-18

ACS Energy Letters

Abstract:For the current passivation strategy, pure iodine passivation during solid-state ligand exchange (SSE) cannot completely passivate the entire surface of PbS colloidal quantum dots (CQDs). Here, a simple stepwise passivation strategy is proposed based on the postpassivation of PbS CQD films with a halogen (Cl, Br, or I) after iodine passivation through the SSE. This postpassivation could compensate for the missing ligands caused by the polar environment during the SSE. Thus, both electron- and hole-trapping states are greatly reduced, and the charge transport in the CQD film is significantly improved. The PbS CQD films post-treated with chlorine exhibit a carrier diffusion length increased by 70% when compared with that of control samples. We demonstrate the highest power conversion efficiency of 12.4% among the reported PbS CQD solar cells prepared with the SSE method to date. In addition, the unencapsulated device shows good stability in air.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsenergylett.0c01561?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsenergylett.0c01561</a>.Materials and characterizations; device fabrication and measurements; synthesis of PbS quantum dots and ZnO nanoparticles; EI, TA, UV–vis, SCLC, XPS, FTIR, AFM, and J–V characterization; performance parameters of device optimization; and diffusion length calculation (<a class="ext-link" href="/doi/suppl/10.1021/acsenergylett.0c01561/suppl_file/nz0c01561_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology,energy & fuels,electrochemistry
Low-Temperature-Processed ZnO Electron Transport Layers for PbS Colloidal Quantum Dot-Based Solar Cells

Rabia Bashir,Muhammad Kashif Bilal,Waqar Ahmad,Amna Bashir,Sana Ullah Asif,Huan Liu,Jiyang Xie,Awais Ali,Wanbiao Hu

DOI: https://doi.org/10.1021/acsanm.1c01510

IF: 6.14

2021-09-08

ACS Applied Nano Materials

Abstract:As an important electron transport layer (ETL) oxide, ZnO has been explored in colloidal quantum dot solar cells (CQDSCs), showing excellent power conversion efficiency (PCE), which however is significantly undermined when being subject to a low-temperature synthesis. To this end, in terms of utilizing 2-aminoethanol as a stabilizing ligand, highly stable ZnO nanoparticles were synthesized through a low-temperature (∼120 °C) reflux method and further utilized for the fabrication of the PbS CQDSCs, which were synthesized by oleic acid and 1-octadecence-assisted PbO decomposition strategy. The champion device with a configuration of glass/ITO/ZnO/PbS-EMII/PbS-EDT/Au achieves a high fill factor (FF) of 74.8% and appreciable PCE of 10.96%, slightly higher than that of the reference device with a ZnO ETL fabricated at 200 °C. This could be related to the high recombination resistance (Rrec of ∼465.8 ohms under light conditions) for the ZnO ETL-based PbS CQDSCs. What is more, these CQDSC devices demonstrate outstanding storage stability in an ambient environment, i.e., over 99% retention in PCE after 150 day storage. As highly efficient and stable CQDSCs are achieved, this work suggests a low-temperature strategy for ETL exploration. Our results may help to pave a feasible way for the development of low-temperature flexible PbS CQD solar cells.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsanm.1c01510.X-ray photoelectron spectroscopy (XPS) of ZnO NPs, current–voltage (I–V) measurements of ZnO NPs annealed at different temperatures in dark conditions, wide-scan convey spectra and O 1s XPS peaks of EMII-treated PbS CQDs, current density–voltage (J–V) curves and EQE spectra of ZnO-based PbS CQDSCs annealed at different temperatures, summarized solar cell parameters for ZnO films annealed at 120 and 200 °C, and comparison table of ZnO-based PbS CQDSC devices with other related literature.This article has not yet been cited by other publications.

materials science, multidisciplinary,nanoscience & nanotechnology
Efficient and Stable PbS Quantum Dot Solar Cells by Triple-Cation Perovskite Passivation

Miguel Albaladejo-Siguan,David Becker-Koch,Alexander D. Taylor,Qing Sun,Vincent Lami,Pola Goldberg Oppenheimer,Fabian Paulus,Yana Vaynzof

DOI: https://doi.org/10.1021/acsnano.9b05848

2020-07-29

Abstract:Solution-processed quantum dots (QDs) have a high potential for fabricating low cost, flexible and large-scale solar energy harvesting devices. It has recently been demonstrated that hybrid devices employing a single monovalent cation perovskite solution for PbS QD surface passivation exhibit enhanced photovoltaic performance when compared to standard ligand passivation. Herein we demonstrate that the use of a triple cation Cs0.05(MA0.17FA0.83)0.95Pb(I0.9Br0.1)3 perovskite composition for surface passivation of the quantum dots results in highly efficient solar cells, which maintain 96 % of their initial performance after 1200h shelf storage. We confirm perovskite shell formation around the PbS nanocrystals by a range of spectroscopic techniques as well as high-resolution transmission electron microscopy. We find that the triple cation shell results in a favorable energetic alignment to the core of the dot, resulting in reduced recombination due to charge confinement without limiting transport in the active layer. Consequently, photovoltaic devices fabricated via a single-step film deposition reached a maximum AM1.5G power conversion efficiency of 11.3 % surpassing most previous reports of PbS solar cells employing perovskite passivation.

Applied Physics,Materials Science
Merging Passivation in Synthesis Enabling the Lowest Open‐Circuit Voltage Loss for PbS Quantum Dot Solar Cells

Yang Liu,Hao Wu,Guozheng Shi,Yusheng Li,Yiyuan Gao,Shiwen Fang,Haodong Tang,Wei Chen,Tianshu Ma,Irfan Khan,Kai Wang,Changlei Wang,Xiaofeng Li,Qing Shen,Zeke Liu,Wanli Ma

DOI: https://doi.org/10.1002/adma.202207293

IF: 29.4

2022-11-17

Advanced Materials

Abstract:The high open‐circuit voltage (Voc) loss arising from insufficient surface passivation is the main factor that limits the efficiency of current PbS colloidal quantum dots (CQDs) solar cell. Here, we perform synergistic passivation in the direct synthesis of conductive PbS CQD inks by introducing multifunctional ligands to well coordinate the complicated CQDs surface with the thermodynamically optimal configuration. The improved passivation effect is intactly delivered to the final photovoltaic device, leading to an order lower surface trap density and beneficial doping behavior compared to the control sample. The obtained CQD inks show the highest PLQY of 24% for all photovoltaic PbS CQD inks, which is more than twice the reported average PLQY value of ཞ10%. As a result, a high Voc of 0.71 V and PCE of 13.3% is achieved, which results in the lowest Voc loss (0.35 eV) for the reported PbS CQD solar cells with PCE >10%, comparable to that of perovskite solar cells. Our work provides valuable insights into the future CQDs passivation strategies and also demonstrates the great potential for the direct‐synthesis protocol of PbS CQDs. This article is protected by copyright. All rights reserved

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Interfacial Heterojunction Enables High Efficient PbS Quantum Dot Solar Cells

Li Zhang,Yong Chen,Shuang Cao,Defei Yuan,Xu Tang,Dengke Wang,Yajun Gao,Junjie Zhang,Yongbiao Zhao,Xichuan Yang,Zhenghong Lu,Quli Fan,Bin Sun

DOI: https://doi.org/10.1002/advs.202402756

IF: 15.1

2024-01-01

Advanced Science

Abstract:AbstractColloidal quantum dots (CQDs) are promising optoelectronic materials for solution‐processed thin film optoelectronic devices. However, the large surface area with abundant surface defects of CQDs and trap‐assisted non‐radiative recombination losses at the interface between CQDs and charge‐transport layer limit their optoelectronic performance. To address this issue, an interface heterojunction strategy is proposed to protect the CQDs interface by incorporating a thin layer of polyethyleneimine (PEIE) to suppress trap‐assisted non‐radiative recombination losses. This thin layer not only acts as a protective barrier but also modulates carrier recombination and extraction dynamics by forming heterojunctions at the buried interface between CQDs and charge‐transport layer, thereby enhancing the interface charge extraction efficiency. This enhancement is demonstrated by the shortened lifetime of carrier extraction from 0.72 to 0.46 ps. As a result, the resultant PbS CQD solar cells achieve a power‐conversion‐efficiency (PCE) of 13.4% compared to 12.2% without the heterojunction.
Potentiation of carcinostasis by combinations of thioguanine and 6-mercaptopurine.

J. Henderson,I. Junga

DOI: https://doi.org/10.1016/0006-2952(60)90020-4

IF: 6.1

1960-10-01

Biochemical Pharmacology

Abstract:
In-situ surface patch-passivation via phosphorus oxygen bond for efficient PbS colloidal quantum dot infrared solar cells

Qi Xiao,Bing Xia,Peilin Liu,Yang Yang,Gaoyuan Yang,Jing Liu,Shuaicheng Lu,Xuezhi Zhao,Ciyu Ge,Duo Chen,Junrui Yang,Guijie Liang,Kanghua Li,Xinzheng Lan,Zewen Xiao,Jianbing Zhang,Liang Gao,Jiang Tang

DOI: https://doi.org/10.1016/j.solmat.2022.112040

IF: 6.9

2022-12-01

Solar Energy Materials and Solar Cells

Abstract:PbS colloidal quantum dots (CQDs) have been widely applied in infrared (IR) solar cells, as they can broaden the photon conversion region beyond 1100 nm, which can help promote an extra 6% of power conversion efficiency (PCE) as bottom subcells for silicon solar cell. Although halide liquid exchange is the dominant passivation strategy for CQDs, it is difficult to passivate all the surface defects, especially for IR CQD, which leaves the main limitation for improving PCE. Here, a facile in-situ solution-processed patch-passivation strategy was first proposed for developing efficient PbS CQD IR solar cells. A typical Lewis base triphenylphosphine oxide (TPPO) was added to I−/Br− capped PbS CQDs, aiming at passivation with uncoordinated Pb2+ as a “patch-ligand”. As a result, the phosphorus oxygen bond coordination could help suppress the non-radiative recombination in CQD films. The TPPO-passivated devices delivered an IR PCE as high as 1.36% under silicon-filtered AM 1.5G, along with a promising open-circuit voltage (VOC) of 0.44 V, both of which are the highest among other single-junction solar cells with a band gap of ∼0.95 eV. The significant VOC and fill factor (FF) enhancement can be attributed to the decrease in defect density and faster charge transport in TPPO-passivated devices.

materials science, multidisciplinary,physics, applied,energy & fuels
Electric field enhanced with CdS/ZnS quantum dots passivation for efficient and stable perovskite solar cells

Cong Li,Huan Li,Zhinan Zhu,Tong Yin,Zhenni Wang,Peipei Li,Chengxin Zeng,Fu Yang,Peng Zhong,Nuanyang Cui,Chunhui Shou

DOI: https://doi.org/10.1016/j.jpowsour.2022.231519

IF: 9.2

2022-07-30

Journal of Power Sources

Abstract:The potential loss caused by defects is one of the most important factors affecting the performance of perovskite photovoltaic devices. CdS/ZnS quantum dots (QDs) have good hydrophobicity and can achieve the dual effects of waterproofing hydrophobic and defect passivation of perovskite films. The Lowest Unoccupied Molecular Orbital (LUMO) energy level of CdS/ZnS QDs doped perovskite film decreases from −3.75 eV to −3.85 eV. The barrier of photo-generated charge transport from the perovskite layer to the electron transport layer is significantly reduced, which is conducive to the enhancement of built-in potential. The density of trap states is reduced and the non-radiative recombination of carriers is suppressed. CdS/ZnS QDs doped perovskite film is dense and has a lower roughness, which helps to increase the contact area with the electron transport layer, thereby improving the charge transportation. Finally, the highest efficiency of the device with QDs reaches 21.36%, and the open-circuit voltage (Voc) and the short-circuit current density (Jsc) are significantly increased compared with undoped ones. The hydrophobicity and stability of the device have also been improved. Therefore, the effect of CdS/ZnS QDs on passivation may provide new ideas for the efficient and stable perovskite solar cells.

energy & fuels,materials science, multidisciplinary,electrochemistry,chemistry, physical
Optimizing Surface Passivation of n‐Type Quantum Dots for Efficient PbS Quantum Dot Solar Cells

Tengzuo Huang,Chunyan Wu,Zuyan Chen,Shuang Shen,Jinpeng Yang,Wei Xu,Kai Kang,Tao Sun,Chaoyu Xiang

DOI: https://doi.org/10.1002/solr.202400073

IF: 9.1726

2024-02-25

Solar RRL

Abstract:The n‐type quantum dot active layer is the core component of lead sulfide quantum dot solar cells (PbS QDSCs). In the state‐of‐the‐art PbS QDSCs, the active layer is commonly obtained through liquid‐phase ligand exchange. Adjusting the ratio between halide ligands and the original PbS QD (oleic acid ligands) during the liquid‐phase ligand exchange process is crucial for achieving better surface passivation of QDs by short‐chain halides, as well as reducing surface defects of the QDs. Due to the intricate chemical state of the ligand exchange solution providing halide ligand, therefore, we used the original QD (PbS‐OA QD) solutions at concentrations of 20 mg/ml, 30 mg/ml, and 40 mg/ml for liquid‐phase ligand exchange, aiming to investigate the reasons for the formation of different surface states post‐exchange and their impact on device performance. The results indicate that when the concentration of the PbS‐OA QD solution is 30 mg/ml, the exchanged QDs exhibit complete removal of surface OA, a higher content of short‐chain ligand PbX2 (X=I, Br), achieving optimal passivation, and a significant reduction in surface defects. Consequently, devices fabricated using PbS‐PbX2 QD ink obtained through the exchange of 30 mg/ml PbS‐OA QD solution achieved a higher power conversion efficiency (PCE) of 12.53%. This study presents a simple and effective strategy to enhance the performance of PbS QDSCs. This article is protected by copyright. All rights reserved.

energy & fuels,materials science, multidisciplinary
Probing and Controlling Surface Passivation of PbS Quantum Dot Solid for Improved Performance of Infrared Absorbing Solar Cells

Xiaoliang Zhang,Ute B. Cappel,Donglin Jia,Qisen Zhou,Juan Du,Tamara Sloboda,Sebastian Svanstrom,Fredrik O. L. Johansson,Andreas Lindblad,Erika Giangrisostomi,Ruslan Ovsyannikov,Jianhua Liu,Hakan Rensmo,James M. Gardner,Erik M. J. Johansson

DOI: https://doi.org/10.1021/acs.chemmater.9b00742

IF: 10.508

2019-01-01

Chemistry of Materials

Abstract:Surface properties of colloidal quantum dots (CQDs) are critical for the transportation and recombination of the photoinduced charge carrier in CQD solar cells, therefore dominating the photovoltaic performance. Herein, PbS CQD passivated using liquid-state ligand exchange (LSLX) and solid-state ligand exchange (SSLX) strategies are in detail investigated using photoelectron spectroscopy (PES), and solar cell devices are prepared to understand the link between the CQD surface properties and the solar cell function. PES using different energies in the soft and hard Xray regime is applied to study the surface and bulk properties of the CQDs, and the results show more effective surface passivation of the CQDs prepared with the LSLX strategy and less formation of lead-oxide. The CQD solar cells prepared with LSLX strategy show higher performance, and the photoelectric measurements suggest that the recombination of photoinduced charges is reduced for the solar cell prepared with the LSLX approach. Meanwhile, the fabricated solar cells exhibit good stability. This work provides important insights into how to fine-tune the CQD surface properties by improving the CQD passivation, and how this is linked to further improvements of the device photovoltaic performance.
Interfacial Engineering Dominated Passivation Strategy to Facilitate Performance Improvement of Cssncl3 Pscs by Induced Sn-O Bonds: Insight from Dft Calculations and Device Simulations

Guanghui Lei,Bo Zhang,Xiang Cheng,Ronghui Xia,Tao Liu,Wei Zhao

DOI: https://doi.org/10.1016/j.cej.2024.153866

IF: 15.1

2024-01-01

Chemical Engineering Journal

Abstract:Defect passivation of perovskite surface not only reduces non-radiative recombination due to defect trapping charge, but also modulates the interfacial structure and energy levels, making it an effective means of solving the stability problem of perovskite materials. This work provides a passivation strategy for CsSnCl3 perovskite, and the interfacial interactions between CsSnCl3 and the passivation agent (PbSO4 and PbCO3) are explored based on first-principles density functional theory. By introducing PbSO4 and PbCO3 with multifunctional quantum dots, strong Sn-O bonds are formed with unsaturated coordination and dangling bonds on the surface of CsSnCl3. Binding sites of water molecules and impurities would be occupied by these bonds, to achieve surface passivation and dehumidification effects, and significantly improve the optical properties of CsSnCl3. PbCO3/SnCl and PbSO4/SnCl constructed the satisfactory interfacial energy level structures. PbCO3/SnCl exhibited excellent light absorption performance ranging in 0 similar to 1200 nm. Introducing PbSO4 and PbCO3 reduced the refractive index of CsSnCl3 exhibiting excellent extinction properties. According to the simulation of Solar Design, perovskite solar cells (PSCs) constructed by (PbSO4, PbCO3)/CsSnCl3 as the active layer achieved power conversion efficiencies of 15.1946 % and 17.3783 %, respectively. This work's research and design results provide a passivation strategy and PSCs design scheme for CsSnCl3 surface defects, which is of great significance for further modification of CsSnCl3 to better apply in photovoltaic field.
Efficient and stable perovskite solar cells thanks to dual functions of oleyl amine-coated PbSO4(PbO)4 quantum dots: Defect passivation and moisture/oxygen blocking

Chong Chen,Fumin Li,Liangxin Zhu,Zhitao Shen,Yujuan Weng,Qiang Lou,Furui Tan,Gentian Yue,Qingsong Huang,Mingtai Wang

DOI: https://doi.org/10.1016/j.nanoen.2019.104313

IF: 17.6

2020-02-01

Nano Energy

Abstract:The defects in perovskite crystals and the penetration of moisture/oxygen into the perovskite layer are major problems for perovskite solar cells (PSCs) to achieve long-term stability and high power conversion efficiency (PCE). However, there is still a lack of multifunctional passivation materials to solve these problems. Herein, for the first time, we report oleyl amine-coated PbSO4(PbO)4 quantum-dots (QDs), as a passivation material with dual functions to simultaneously passivate the surface defects and block the penetration of moisture/oxygen into the perovskite layer for stable and efficient PSCs. The PbSO4(PbO)4 QDs significantly reduce the defect density of the as-prepared CH3NH3PbI3 films by passivating under-coordinated Pb ions and I anions and effectively enhance charge extraction efficiency at the TiO2/CH3NH3PbI3 and CH3NH3PbI3/spiro-OMeTAD interfaces. Moreover, the hydrogen bond between H atoms of the OA and I atoms of the perovskite and the interface electric field at CH3NH3PbI3/OA interface also contribute to the improvement of efficiency and stability of PSCs. Finally, higher PCE (20.02%) is achieved by the PSCs with OA-coated PbSO4(PbO)4 QDs compared to that (16.86%) of the PSCs without OA-coated PbSO4(PbO)4, corresponding to a 18.7% enhancement. Moreover, the PSCs with OA-coated PbSO4(PbO)4 QDs maintain 90% of initial efficiency after operation for 280 h, indicating better stability than the PSCs without PbSO4(PbO)4 QDs.

materials science, multidisciplinary,chemistry, physical,physics, applied,nanoscience & nanotechnology
In Situ Passivation for Efficient PbS Quantum Dot Solar Cells by Precursor Engineering

Yongjie Wang,Kunyuan Lu,Lu Han,Zeke Liu,Guozheng Shi,Honghua Fang,Si Chen,Tian Wu,Fan Yang,Mengfan Gu,Sijie Zhou,Xufeng Ling,Xun Tang,Jiawei Zheng,Maria Antonietta Loi,Wanli Ma

DOI: https://doi.org/10.1002/adma.201704871

IF: 29.4

2018-03-15

Advanced Materials

Abstract:Current efforts on lead sulfide quantum dot (PbS QD) solar cells are mostly paid to the device architecture engineering and postsynthetic surface modification, while very rare work regarding the optimization of PbS synthesis is reported. Here, PbS QDs are successfully synthesized using PbO and PbAc2 · 3H2 O as the lead sources. QD solar cells based on PbAc-PbS have demonstrated a high power conversion efficiency (PCE) of 10.82% (and independently certificated values of 10.62%), which is significantly higher than the PCE of 9.39% for PbO-PbS QD based ones. For the first time, systematic investigations are carried out on the effect of lead precursor engineering on the device performance. It is revealed that acetate can act as an efficient capping ligands together with oleic acid, providing better surface coverage and replace some of the harmful hydroxyl (OH) ligands during the synthesis. Then the acetate on the surface can be exchanged by iodide and lead to desired passivation. This work demonstrates that the precursor engineering has great potential in performance improvement. It is also pointed out that the initial synthesis is an often neglected but critical stage and has abundant room for optimization to further improve the quality of the resultant QDs, leading to breakthrough efficiency.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Quantum Dot Interface-Mediated CsPbIBr 2 Film Growth and Passivation for Efficient Carbon-Based Solar Cells

Xingnan Qi,Jiantao Wang,Furui Tan,Chen Dong,Kong Liu,Xiaobao Li,Lisheng Zhang,Hongkai Wu,Hsing-Lin Wang,Shengchun Qu,Zhanguo Wang,Zhijie Wang

DOI: https://doi.org/10.1021/acsami.1c16290

2021-11-11

Abstract:CsPbIxBry-based all-inorganic perovskite materials are a potential candidate for stable semitransparent and tandem structured photovoltaic devices. However, poor film (morphological and crystalline) quality and interfacial recombination lead consequently to a decline in the photoelectric conversion performance of the applied solar cells. In this work, we incorporated PbS quantum dots (QDs) at the interface of electron transporting layer (ETL) SnO2 and perovskite to modulate the crystallization of CsPbIBr2 and the interfacial charge dynamics in carbon-based solar cells. The as-casted PbS QDs behave as seeds for lattice-matching the epitaxial growth of pinhole-free CsPbIBr2 films. The modified films with reduced defect density exhibit facilitated carrier transfer and suppressed charge recombination at the ETL/perovskite interface, contributing to an enhanced device efficiency from 7.00 to 9.09% and increased reproducibility and ambient stability. This strategic method of QD-assisted lattice-matched epitaxial growth is promising to prepare high-quality perovskite films for efficient perovskite solar cells.

materials science, multidisciplinary,nanoscience & nanotechnology
Zn‐Porphyrin Antisolvent Engineering Enhanced Grain Boundary Passivation for High‐Performance Perovskite Solar Cell

Abdul Kareem Kalathil Soopy,Bhaskar Parida,S. Assa Aravindh,Hiba SahulHameed,Bhabani Sankar Swain,Na'il Saleh,Inas Magdy Abdelrahman Taha,Dalaver Hussain Anjum,Vivian Alberts,Shengzhong Liu,Adel Najar,Assa S. Aravindh,Na’il Saleh,Shengzhong (Frank) Liu

DOI: https://doi.org/10.1002/solr.202400054

IF: 9.1726

2024-03-22

Solar RRL

Abstract:Perovskite solar cells (PSCs) represent a promising and rapidly evolving technology in the field of photovoltaics due to their easy fabrication, low‐cost materials, and remarkable efficiency improvements over a relatively short period. However, the grain boundaries in the polycrystalline films exhibit a high density of defects, resulting in not only heightened reactivity to oxygen and water but also hampered charge transport and long‐term stability. In this study, we present an approach involving Zn‐porphyrin (Zn‐PP) upgraded anti‐solvent treatment to enhance the grain size and meanwhile passivate grain boundary defects in FA0.95MA0.05PbI2.85Br0.15 perovskites. The Zn‐PP molecules significantly improve structural and optical properties, effectively mitigating defects and promoting carrier transport at the perovskite/hole transport layer interface. The DFT simulation confirms that Zn‐PP forms a strong chemical bonding with the perovskite surface. With the Zn‐PP passivation, the total DOS shifts to higher energy regions with molecular adsorption, especially near the valence and conduction band edges, indicating that there is an increase in conducting properties of the surface with molecular adsorption. The power conversion efficiency (PCE) of PSCs enhanced significantly as a result of this improvement, rising from 15.38% to 19.11%. Moreover, unencapsulated PSCs treated with Zn‐PP exhibit outstanding stability, retaining over 91% of their initial PCE. This article is protected by copyright. All rights reserved.

energy & fuels,materials science, multidisciplinary
Enhanced electron extraction using SnO2 for high-efficiency planar-structure HC(NH2)2PbI3-based perovskite solar cells

Qi Jiang,Liuqi Zhang,Haolin Wang,Xiaolei Yang,Junhua Meng,Heng Liu,Zhigang Yin,Jinliang Wu,Xingwang Zhang,Jingbi You

DOI: https://doi.org/10.1038/nenergy.2016.177

IF: 56.7

2016-11-14

Nature Energy

Abstract:Planar structures for halide perovskite solar cells have recently garnered attention, due to their simple and low-temperature device fabrication processing. Unfortunately, planar structures typically show I–V hysteresis and lower stable device efficiency compared with mesoporous structures, especially for TiO2-based n-i-p devices. SnO2, which has a deeper conduction band and higher electron mobility compared with traditional TiO2, could enhance charge transfer from perovskite to electron transport layers, and reduce charge accumulation at the interface. Here we report low-temperature solution-processed SnO2 nanoparticles as an efficient electron transport layer for perovskite solar cells. Our SnO2-based devices are almost free of hysteresis, which we propose is due to the enhancement of electron extraction. By introducing a PbI2 passivation phase in the perovskite layer, we obtain a 19.9 ± 0.6% certified efficiency. The devices can be easily processed under low temperature (150 ∘C), offering an efficient method for the large-scale production of perovskite solar cells.

materials science, multidisciplinary,energy & fuels
Perovskite solar cell with improved performance passivated by all inorganic perovskite quantum dots

Jia Xing Cao,Hui Feng Shen,Lei Cheng,Wen Tao Zhao,Dong Huan Zhu,Yan Sun,Bo Ni

DOI: https://doi.org/10.1088/1742-6596/1885/2/022019

2021-04-01

Journal of Physics: Conference Series

Abstract:Abstract Improving the efficiency and stability of perovskite solar cells is the main direction of realizing their commercial application. Interface passivation is one of the most effective methods. Through interface passivation, on the one hand, the energy level of the device can be adjusted and the photoelectric conversion efficiency (PCE) of the device can be improved; on the other hand, materials that are not sensitive to the environment can be selected to improve the stability of the device. All inorganic perovskite quantum dots (QDs) have excellent environmental stability and are similar to the crystal structure of the absorbing layer of perovskite solar cells, so they have the potential for interface passivation. In this paper, two kinds of all inorganic perovskite QDs with different morphology, size and crystal structure were synthesized by hot injection method, which were used as the passivation layer of perovskite solar cells, and improved the device performance. The PCE of the device treated with CsPbBr 3 QDs can reach as high as 20.45%, and has excellent environmental stability.
Air fabrication of SnO2 based planar perovskite solar cells with an efficiency approaching 20%: Synergistic passivation of multi-defects by choline chloride

Zhipeng Wang,Rui Li,Mei Zhang,Min Guo

DOI: https://doi.org/10.1016/j.ceramint.2021.09.096

IF: 5.532

2022-01-01

Ceramics International

Abstract:Defects in the perovskite films impose a serious issue on the PCE and stability of the SnO2 based planar perovskite solar cells (SP–PSCs). So far, most researches have focused on regulating the SnO2/perovskite interface to improve performance. However, defect passivation of the perovskite/HTM interface is more significant and potential. Herein, the non-toxic and cheap choline chloride was performed to passivate multiple defects of the MAPbI3/HTM interface in ambient atmosphere. An optimal PCE of 19.93% (the average PCE was 18.60%) was obtained for the passivated device. Furthermore, the effect and mechanism of choline chloride on the humid and thermal stability of the SP-PSCs was investigated in detail. The passivated device without encapsulation retained 91% of its initial efficiency after 20 days in humid environment (20 ± 5 °C, 55 ± 5% RH) and 95% of the initial value under heating for 7 cycles (85 °C). Chloride ions with smaller radius and larger electronegativity formed stronger ionic bonding with Pb2+ to passivate I− vacancy defects, while choline ions passivated MA+ vacancies. This work not only provides guidance for fabrication of an efficient and stable device in air, but also opens an avenue to understanding of relation between stability and defects in the SP-PSCs.

materials science, ceramics
Efficient PbS Quantum Dot Solar Cells Employing a Conventional Structure

Kunyuan Lu,Yongjie Wang,Jianyu Yuan,Zequn Cui,Guozheng Shi,Shaohua Shi,Lu Han,Si Chen,Yannan Zhang,Xufeng Ling,Zeke Liu,Lifeng Chi,Jian Fan,Wanli Ma

DOI: https://doi.org/10.1039/c7ta07014d

IF: 11.9

2017-01-01

Journal of Materials Chemistry A

Abstract:New-generation solar cells based on colloidal lead chalcogenide (PbX) quantum dots (CQDs) are promising low-cost solution-processed photovoltaics.
Passivation Mechanism of Perovskite Upper Interface based on MAPbBr3 Quantum Dots for Efficient and Stable Perovskite Solar Cells

Yan Feng,Huilin Li,Zhitao Shen,Fumin Li,Mengqi Jin,Yanjing Rong,Xingyuan Tian,Rong Liu,Chong Chen

DOI: https://doi.org/10.2139/ssrn.4379517

IF: 6.813

2023-08-29

Sustainable Energy & Fuels

Abstract:The high quality perovskite film plays a key role in the efficient perovskite solar cells (PSCs). It is an effective way to obtain high quality perovskite films via post treatment. In our latest work, a synergistic co-passivation strategy of sequentially using functional oleyl amine-coated MAPbBr3 quantum dots (M-QDs) and n-octylammonium iodide (OAI) solutions to treat the perovskite layer was reported. Herein, the M-QDs show good passivation effect. However, the passivation mechanism of M-QDs in PSCs is unclear. Accordingly, by using some powerful tools, we systematically explore the relationship between the nanostructure and optoelectronic properties of perovskite films, and further reveal the internal causes between the passivation at different concentrations of M-QDs and the performance of Cs0.05(FA0.85MA0.15)0.95Pb(I0.85Br0.15)3-based PSCs. After being treated by an appropriate concentration (0.3 mM) of M-QDs, the perovskite film displays very good crystallinity, flatness and compactness, resulting to an optimized PCE of ~21% along with a high open circuit voltage of 1.17 V. Moreover, the optimized PSC without encapsulation shows excellent stability both in N2 and air environment.

materials science, multidisciplinary,chemistry, physical,energy & fuels

Low-temperature-processed SnO2–Cl for Efficient PbS Quantum-Dot Solar Cells Via Defect Passivation

Passivation Strategy of Reducing Both Electron and Hole Trap States for Achieving High-Efficiency PbS Quantum-Dot Solar Cells with Power Conversion Efficiency over 12%

Low-Temperature-Processed ZnO Electron Transport Layers for PbS Colloidal Quantum Dot-Based Solar Cells

Efficient and Stable PbS Quantum Dot Solar Cells by Triple-Cation Perovskite Passivation

Merging Passivation in Synthesis Enabling the Lowest Open‐Circuit Voltage Loss for PbS Quantum Dot Solar Cells

Interfacial Heterojunction Enables High Efficient PbS Quantum Dot Solar Cells

Potentiation of carcinostasis by combinations of thioguanine and 6-mercaptopurine.

In-situ surface patch-passivation via phosphorus oxygen bond for efficient PbS colloidal quantum dot infrared solar cells

Electric field enhanced with CdS/ZnS quantum dots passivation for efficient and stable perovskite solar cells

Optimizing Surface Passivation of n‐Type Quantum Dots for Efficient PbS Quantum Dot Solar Cells

Probing and Controlling Surface Passivation of PbS Quantum Dot Solid for Improved Performance of Infrared Absorbing Solar Cells

Interfacial Engineering Dominated Passivation Strategy to Facilitate Performance Improvement of Cssncl3 Pscs by Induced Sn-O Bonds: Insight from Dft Calculations and Device Simulations

Efficient and stable perovskite solar cells thanks to dual functions of oleyl amine-coated PbSO4(PbO)4 quantum dots: Defect passivation and moisture/oxygen blocking

In Situ Passivation for Efficient PbS Quantum Dot Solar Cells by Precursor Engineering

Quantum Dot Interface-Mediated CsPbIBr 2 Film Growth and Passivation for Efficient Carbon-Based Solar Cells

Zn‐Porphyrin Antisolvent Engineering Enhanced Grain Boundary Passivation for High‐Performance Perovskite Solar Cell

Enhanced electron extraction using SnO2 for high-efficiency planar-structure HC(NH2)2PbI3-based perovskite solar cells

Perovskite solar cell with improved performance passivated by all inorganic perovskite quantum dots

Air fabrication of SnO2 based planar perovskite solar cells with an efficiency approaching 20%: Synergistic passivation of multi-defects by choline chloride

Efficient PbS Quantum Dot Solar Cells Employing a Conventional Structure

Passivation Mechanism of Perovskite Upper Interface based on MAPbBr3 Quantum Dots for Efficient and Stable Perovskite Solar Cells