Passivation Strategy of Reducing Both Electron and Hole Trap States for Achieving High-Efficiency PbS Quantum-Dot Solar Cells with Power Conversion Efficiency over 12%

Chao Ding,Feng Liu,Yaohong Zhang,Shuzi Hayase,Taizo Masuda,Ruixiang Wang,Yong Zhou,Yingfang Yao,Zhigang Zou,Qing Shen

DOI: https://doi.org/10.1021/acsenergylett.0c01561

IF: 22

2020-09-18

ACS Energy Letters

Abstract:For the current passivation strategy, pure iodine passivation during solid-state ligand exchange (SSE) cannot completely passivate the entire surface of PbS colloidal quantum dots (CQDs). Here, a simple stepwise passivation strategy is proposed based on the postpassivation of PbS CQD films with a halogen (Cl, Br, or I) after iodine passivation through the SSE. This postpassivation could compensate for the missing ligands caused by the polar environment during the SSE. Thus, both electron- and hole-trapping states are greatly reduced, and the charge transport in the CQD film is significantly improved. The PbS CQD films post-treated with chlorine exhibit a carrier diffusion length increased by 70% when compared with that of control samples. We demonstrate the highest power conversion efficiency of 12.4% among the reported PbS CQD solar cells prepared with the SSE method to date. In addition, the unencapsulated device shows good stability in air.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsenergylett.0c01561?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsenergylett.0c01561</a>.Materials and characterizations; device fabrication and measurements; synthesis of PbS quantum dots and ZnO nanoparticles; EI, TA, UV–vis, SCLC, XPS, FTIR, AFM, and <i>J</i>–<i>V</i> characterization; performance parameters of device optimization; and diffusion length calculation (<a class="ext-link" href="/doi/suppl/10.1021/acsenergylett.0c01561/suppl_file/nz0c01561_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology,energy & fuels,electrochemistry

What problem does this paper attempt to address?

The main problem that this paper attempts to solve is to improve the photoelectric conversion efficiency (PCE) of PbS quantum - dot solar cells prepared by the solution - phase ligand - exchange method. Specifically, the researchers found that current passivation strategies cannot completely passivate the entire surface of PbS colloidal quantum dots (CQDs) during the solid - state ligand - exchange (SSE) process. In particular, when ligand - exchange is carried out in a polar environment (such as methanol and DMF), it is easy to cause the desorption of weakly - bound ligands (such as oleic acid and iodide ions) on the CQDs surface, especially the ligands on the non - polar (100) plane. These ligands have a lower density and weaker binding energy, making the (100) plane surface prone to form trap states, thus affecting the performance of solar cells.

To solve this problem, the paper proposes a new step - by - step passivation strategy, that is, post - passivating PbS CQD films with halogens (Cl, Br or I) by the SSE method after iodine passivation. This post - passivation can compensate for the missing ligands due to the polar environment in the SSE process, thereby greatly reducing electron and hole trap states and significantly improving charge transport in CQD films. In particular, the carrier diffusion length of PbS CQD films after chlorine post - treatment is 70% longer than that of the control sample, and a maximum power conversion efficiency of up to 12.4% has been achieved, which is the highest value reported so far for PbS CQD solar cells prepared by the SSE method. In addition, the unpackaged device shows good stability in air.