Abstract:The enhancement of cryogenic plasticity for some aluminum alloys has attracted broad attention, which provides a new approach to the formability improvement of high-strength aluminum alloys. However, the hardening behavior and the ductility of aluminum alloys at cryogenic temperatures are very sensitive to the microstructure tempered at different conditions, with complex combination of GP zones, second phase precipitates, coarse and equilibrium phases. In this paper, three groups of tempered AA7075 aluminum alloy sheets are elaborately designed by means of different approaches, i.e., solution-treated (W), peak artificial aged (T6), and fast re-dissolved (FD) from T6, to investigate their cryogenic deformation behavior and failure mechanism. The effect on cryogenic plasticity of second phases, including the coarse particles in the matrix and the precipitate free zones (PFZs) accompanied by chain distributed particles along grain boundary, can be isolated by comparison among these three kinds of AA7075 alloys. The cryogenic mechanical properties of AA7075 sheets are evaluated by uniaxial tensile test, and the microstructure evolution observed by transmission electron microscope (TEM), scanning electron microscope (SEM) and laser confocal microscope (LCM). It shows that the enhancement of both ductility and continuous work hardening for W- and FD-tempered AA7075 sheets at cryogenic temperatures results from the uniformly distributed dislocations in the matrix of supersaturated solid solution (SSSS). The relatively low cryogenic ductility of AA7075-FD in comparison with AA7075-W results from the cracked η phases in the interior of grain, which has an increasing brittleness and high stresses on the particle due to the bypassing process at cryogenic condition. Furthermore, the undesirable early fracture of AA7075-T6 alloy during cryogenic deformation process is systematically illustrated from the aspect of interaction between dislocation and second-phase particles. Beside the cracked η phases in the interior of grains, defects also appear in the non-coherent interface between PFZ and the equilibrium η phase due to stain localization at grain boundary. As a result, AA7075-T6 alloy exhibits a ductile-brittle mixed fracture mode dominated by PFZ and the equilibrium η phase at grain boundary.

Mechanical Properties and Cold Cracking Evaluations of Four 7××× Series Aluminum Alloys Using a Newly Developed Index

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Fabrication and Properties of Al-Cu-Mg-Zn Series Alloys with Low Hot Cracking Tendency for Liquid Forging

Microstructure Evolution and Mechanical Properties of a Cast and Heat-Treated Al–Li–Cu–Mg Alloy: Effect of Cooling Rate During Casting

Achieving Low Hot Tearing Susceptibility in High-Strength Cast Al-Li Alloys: Experimental Investigation and Simulation Assessment

Effect of Zn/Mg/Cu Additions on Hot Cracking Tendency and Performances of Al-Cu-Mg-Zn Alloys for Liquid Forging

Experimental Investigation and Simulation Assessment on Fluidity and Hot Tearing Susceptibility of Al-Li-Cu-X Alloy: the Role of Microalloying Elements

Correlation of Solidification Microstructure Refining Scale, Mg Composition and Heat Treatment Conditions with Mechanical Properties in Al-7Si-Mg Cast Aluminum Alloys

Modeling the Precipitation Kinetics and Tensile Properties in Al-7si-Mg Cast Aluminum Alloys

Sustainability through Optimal Compositional and Thermomechanical Design for the Al-7XXX Alloys: An ANOVA Case Study

Experimental and Numerical Investigation on Strengthening Behavior of 7075 Aluminum Alloy Sheets in Hot Forming–Quenching Integrated Process

Cryogenic Deformation Behavior and Failure Mechanism of AA7075 Alloy Sheets Tempered at Different Conditions

Investigating Thermal and Mechanical Characteristics of Die-Casting Aluminum Alloys: A Comprehensive Investigation via Thermal Analysis

Microstructure and Mechanical Properties of Cast Al-Li-Mg Alloy: Role of Cu Addition and Heat Treatment

Modeling of Strain Hardening Behavior and Mechanical Properties of Al 7Si Mg Cast Aluminum Alloys During Tensile Process

Simulation of Ductile Fracture in an Aluminum Alloy Using Various Criteria

Finite Element Simulation and Experimental Investigation of Hot Forming Cold Die Quenching and Equal Channel Angular Pressing of AA2024 Aluminum Alloy

Cracking Susceptibility and Joint Property Study of the 6061 Aluminum

Cracking criterion for high strength Al–Cu alloys fabricated by selective laser melting

Computational design of a crack-free aluminum alloy for additive manufacturing

Uncovering the effects of local pressure and cooling rates on porosity formation in AA2060 Al-Li Alloy