Abstract:The mechanical and twinning behavior of Mg alloys containing a monolithic texture component have been extensively studied; however, studies on samples with multi texture components are much insufficient. In this study, the quantitative relationship between the mechanical behavior under tension along the extrusion direction (ED) of Mg AZ31 rods and the percentages of bimodal texture components <0002>// ED (19–87%) and <0002>⊥ED were systematically studied. The component <0002>// ED favors <math>{101¯2}</math> twinning and is soft orientations; however, the component <0002>⊥ED favors prismatic slip and is hard orientations. The results show that the yield strength does not decrease linearly with an increase in the percentage of the soft orientations and show a deviation from the calculations using the conventional rule of mixtures. A higher percentage of the soft grains increases this deviation when the percentage is below 50%, and decreases it over 50%. The ultimate strengths, however, do not show an obvious dependence on the percentage of the soft orientations. Subsequently, the corresponding mechanisms are discussed and a modified rule of mixtures was developed. Bimodal texture components stimulate the activation of <math>{101¯2}</math> twin variants with a low Schmid factor and the presence of more variants within one grain. Conventional strain accommodation rule was used to analyze this twinning behavior, but it cannot explain the experimental observations. Crystal-plasticity based finite element modeling was employed to analyze this strange twinning behavior. The results indicate that the interaction among twin variants, rather than deformation in neighboring grains, plays a major role in the activation of twins with a low Schmid factor, due to a hard deformation propagation from the soft grains to the hard grains. This finding provides an important complementation to the strain accommodation theory.

Deformation Behavior and Texture Randomization of Mg–Zn–Gd Alloys Reinforced with Icosahedral Quasicrystal

Effect of quasicrystal and Laves phases on strength and ductility of as-extruded and heat treated Mg–Zn–Gd-based alloys

Effect of Icosahedral Phase on Crystallographic Texture and Mechanical Anisotropy of Mg–4%Li Based Alloys

Quasicrystal phase evolution and mechanical properties of Mg-3.5Zn-0.6Gd alloy processed by high-pressure torsion

Deformation behavior of Mg-Zn-Y icosahedral quasicrystal phase in a magnesium matrix by high pressure torsion at room temperature

Quasicrystal-reinforced Mg alloys

A comprehensive analysis on microstructure evolution of Mg-5.65Zn-0.66Zr alloy during hot deformation

Microstructure and Phase Transformation of Forged Mg–3.7Zn–0.3Y–0.3Gd Quasicrystal Alloy

Effects of Icosahedral Phase on Mechanical Anisotropy of As-Extruded Mg-14Li (in Wt%) Based Alloys

Hot deformation behavior of novel high-strength Mg-0.6Mn-0.5Al-0.5Zn-0.4Ca alloy

Effects of extrusion on the microstructure and mechanical properties of Mg–Zn–Gd alloy reinforced with quasicrystalline particles

Evolution of Deformation Substructure and MgxZnyCaz Metastable Phase in Fine-Grained Mg Alloys

Effect of Bimodal Quasicrystal Phase on the Dynamic Recrystallization of Mg–Zn–Gd Alloy during High-Pressure Torsion

Dynamic Recrystallization, Texture Evolution, and Improved Mechanical Properties of Mg-Y-Zn-V Alloy during Forging and Subsequent Extruding Deformation

Effects of deformation parameters on microstructure and texture of Mg–Zn–Ce alloy

Room-Temperature Strengthening, Portevin-Le Chatelier Effect, High-Temperature Tensile Deformation Behavior, and Constitutive Modeling in a Lightweight Mg-Gd-Al-Zn Alloy

Dynamic Recrystallization-Dependent High-Temperature Tensile Properties and Deformation Mechanisms in Al-Mg-Sc-Zr Alloys

The synergistic and interactive effects of slip systems and dynamic recrystallization on the weakening basal texture of Mg-Y-Nd-Zr-Gd magnesium alloy

A quantitative study on mechanical behavior of Mg alloys with bimodal texture components

Deformation mechanisms of Mg-Ca-Zn alloys studied by means of micropillar compression tests

Enhanced ductility and strength of Mg-1Zn-1Sn-0.3Y-0.2Ca alloy achieved by novel micro-texture design