Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

Reaction Between Cao And Fe3o4 Under Co-Co2 Atmosphere At 800 Degrees C-1 100 Degrees C

New understanding on formation mechanism of CaFe2O4 in Fe2O3 -Fe3O4-CaO-SiO2 system during sintering Process: Phase transformation and morphologies evolution

Nitrogen monoxide reduction by carbon monoxide to combustion control with calcium ferrite redox in iron ore sintering

Synthesis and phase formation mechanism of alpha-Fe2O3 powders by hydrothermal reaction method

Competitive Formation Behavior of Calcium Silicate and Calcium Ferrite in Sintering of Iron Ore Fines

Formation of Calcium Ferrite Containing Aluminum (CFA) in Sintering of Iron Ore Fines

Interfacial Phenomenon and Marangoni Convection of Fe–C Melt on Coke Substrate under in Situ Observation

Effect of ZnO-doping on the Reaction Between Co and Fe Oxides

Effect of FeO concentration in sinter iron ore on reduction behavior in a hydrogen-enriched blast furnace

Diffusion and reaction mechanism of limestone and quartz in fluxed iron ore pellet roasting process

Effect of Al2O3 on Sintering Reaction of Calcium Ferrite

Reaction Characteristics of Phosphogypsum Under Carbon Monoxide Atmosphere

Experimental Phase Equilibria Studies in the FeO-Fe2O3-CaO-Al2O3 System in Air

Reaction Behavior of Al_2O_3 and Fe_2O_3 in Na_2O-Al_2O_3-Fe_2O_3 Systems During Sintering

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

FeO controls the sintering of iron-based oxygen carriers in chemical looping CO2 conversion

Updating mechanism of siderite roasting through insights into reactions between inherent oxides of iron and carbon

Effect of SiO2 on Crystallization of Calcium Ferrites in Fe2O3–CaO–SiO2–Al2O3 System in Cooling Process

Effect of Ca-Fe oxides additives on NOx reduction in iron ore sintering

The Influence of FeO on the Reaction between Fe–Al–Ca Alloy and Al2O3–CaO–FeO Oxide during Heat Treatment at 1473 K

Effect of Cr on isothermal structure transformation of iron oxide scale