Abstract:The "all in one" multifunctional and concentrated daily chemical products are required by the market, such as the long‐term release of anti‐bacterial, medical, or perfume agents. These functions mainly rely on the microcapsules, which could encapsulate these functional and unstable molecules, and then release them in the long term. To stabilize these functional solid particles in a high‐content surfactant, it is necessary to add a suspending rheological modifier. The poly(acrylic acid) (PAA)‐based rheology modifier is one of the most common additives in the industry of daily chemicals, for thickening or suspending. In this paper, linear PAA, and branched PAA polymers (Carbomer 941 and Carbomer 940) were selected to study the suspending ability of PAA‐based rheology modifier in high‐content surfactant and to investigate the effect of PAA polymer structure and Mw on the complex solution's rheological properties. The yield and viscosity test of the complex solutions of linear PAA and high‐content surfactant revealed that the addition of linear PAA could lead to lower yield stress and viscosity, and failed to suspend the polystyrene (PS) model microspheres due to its smaller mean square radius of gyration. The branched PAA polymer, Carbomer 940 and Carbomer 941 were more stable than the linear PAA in these two kinds of surfactant. More specifically, Carbomer 940 with a higher Mw, would exhibit higher yield stress and viscosity than Carbomer 941 with a lower Mw in nonionic surfactant alcohol polyoxyethylene ether (AEO) solvent with content less than 5 wt%. When the content was higher than 5 wt%, Carbomer 941 presented higher yield stress and viscosity than Carbomer 940, and successfully suspended PS microspheres in the 20 wt% AEO solution. This could depend on the polymer chain's elongation state of these two PAA‐based branched rheology modifiers. The same trend happened in the appearance of Carbomer 940 and Carbomer 941 in alcohol ether sulphate (AES) solution. However, the electrostatic repulsive force between the AES and PAA‐based rheology modifier could further make the polymer chain curl up and restrain the suspending ability in a lower content surfactant solution. Therefore, this fundamental research could guide the application of the anionic polyelectrolytes in the concentrated daily chemical product for stable suspending particles.

Study of Structure–performance Relationships of Polymeric Dispersants on Particle Dispersion and Stabilisation

Synergetic Effect of a Reactive Compatibilizer and Organo-montmorillonite on the Dispersion of Polyamide 6 /Polydimethylsilicone Blend with a High Viscosity Ratio

Effect of comb polymer dispersants with different molecular structures on the performance of LiFePO4 suspensions

Preparation and property analysis of polyacrylate dispersant for calcium carbonate

Study on the dispersion mechanism of the polycarboxylic acid dispersant for disperse dyes

Synthesis of Dispersant with Comb-Structure with Application to Copolymerization of Styrene and Divinylbenzene

Effects of Chemical Structure on the Properties of Carboxylate‐type Copolymer Dispersant for Coal‐water Slurry

One-pot Synthesis of Block Copolymer Dispersant by ICAR ATRP with Ppm Copper Catalyst and the Dispersibility on Pigment

Synthesis of a novel amphoteric copolymer and its application as a dispersant for coal water slurry preparation

Effect of Dispersants on the Stability of Calcite in Non-Polar Solutions

Synthesis, Aggregation and Adsorption Behaviour of a Thermoresponsive Pentablock Copolymer

Structured polymer dispersant for efficient phthalocyanine blue dispersion and color paste preparation

Stabilization of ceramics particles with anionic polymeric dispersants

Dissipative Particle Dynamics Study on Interfacial Properties of Symmetric Ternary Polymeric Blends

Improvement in dispersion stability of alumina suspensions and corresponding chemical mechanical polishing performance

Design Selection and Application Research of Waterborne Multi-Functional Dispersants

The suspending appearance of poly(acrylic acid)‐based rheology modifier in high‐content surfactant: The effect of polymer structure and molecular weight on the rheological properties of the complex systems

Poegma-B-Paa Comb-Like Polymer Dispersant For Al-2 Suspensions

Improving the steric hindrance effect of linear sulfonated acetone–formaldehyde dispersant and its performance in coal–water slurry

Influence of dispersant functional group architecture on titania pigment particle interactions

Inter-particle interactions of alumina powders in UV-curable suspensions for DLP stereolithography and its effect on rheology, solid loading, and self-leveling behavior