Abstract:(1)Micromechanical properties of low‐carbon Al2O3–C refractories by grid nanoindentation. (2)Identification and statistical analysis on the indentation results of aggregate, matrix, and aggregate/matrix interface. (3)Brittleness reduction accounted by the increased specific fracture energy of the aggregate/matrix interfacial layer. The mechanical properties at microlevels are of important meaning for refractories while determining these values is of great challenges. In this contribution, a tailored grid nanoindentation test was employed to determine the micromechanical properties of low‐carbon Al2O3–C refractories featuring reduced brittleness with in situ magnesium aluminate spinel/carbon nanotubes (MgAl2O4/CNTs) compound interfacial layer between the aggregate and matrix. The micromechanical properties, especially Young's modulus (E) and specific fracture energy (Gc) of the aggregate, matrix, and aggregate/matrix interface area of the refractories, were determined and compared. Statistical analysis on the nanoindentation results of the aggregate and matrix in the reference sample and the sample with interfacial layer shows high consistency, which reveals the high feasibility of the method. The median microspecific fracture energy of the aggregate/matrix interface increases from 63.67 J m−2 of the reference group to 132.90 J m−2 of the sample with the compound interfacial layer, which means that higher energy is needed for the initiation and propagation of microcracks within the interfacial layer, accounting for the brittleness reduction of the refractories. Consistent conclusions were drawn from the nanoindentation test at microlevels along with the macrolevel thermal shock test and wedge splitting test.

Fracture Behavior of Low Carbon MgO–C Refractories Using the Wedge Splitting Test

Mechanical Behavior and Thermal Shock Resistance of MgO-C Refractories: Influence of Graphite Content

Influence of graphite content on fracture behavior of MgO–C refractories based on wedge splitting test with digital image correlation method and acoustic emission

Effect of particle grading on fracture behavior and thermal shock resistance of MgO-C refractories

Effect of C/MgO nanocomposite powders on the properties of low-carbon MgO–C refractories

Enhanced thermal shock resistance of low‐carbon Al2O3‐C refractories via CNTs/MgAl2O4 whiskers composite reinforcement

A New Approach to Fabricate MgO-C Refractories with High Thermal Shock Resistance by Adding Artificial Graphite

Effect of microporous aggregates and spinel powder on fracture behavior of magnesia-based refractories

Improved thermal shock resistance of magnesia-graphite refractories by the addition of MgO-C pellets

Nanoscale toughening of low carbon Al2O3‐C refractories by means of SiCnw/Al2O3 composite reinforcement

Improved thermal shock resistance of MgO–C refractories with addition of calcium magnesium aluminate (CMA) aggregates

Preparation, properties, and interfacial bonding mechanism of MgO–Mg2SiO4–SiC–C refractories

Enhanced performance of low-carbon MgO–C refractories with nano-sized ZrO2–Al2O3 composite powder

Micromechanical properties of Al2O3–C refractories with aggregate/matrix interfacial layer by nanoindentation

Effect of stainless steel fibers on properties of MgO–C refractories

Improved thermal shock resistance of low-carbon Al2O3–C refractories fabricated with C/MgAl2O4 composite powders

Molten salt synthesis of Cr3C2-coated flake graphite and its effect on the physical properties of low-carbon MgO–C refractories

Improved thermal shock stability and oxidation resistance of low-carbon MgO–C refractories with introduction of SiC whiskers

Effects of Carbon Fiber Addition Amount on Thermal Shock Resistance and Sintering Performance of MgO-ZrO2 Ceramics

Nano-laminated BN modified graphite reinforced unfired MgO–C refractories: Preparation, properties and strengthening mechanism

Mechanical properties and microstructure evolution of MgO–Al–C slide plate refractories in presence of Al powder-modified magnesia aggregates