Abstract:Argon oxygen decarburization (AOD) refining as one type of secondary refining plays an important role in the steel industry. MgO–CaO and MgO–C bricks are widely used in AOD refining, and MgO–CaO bricks are easily hydrated. MgO–C bricks containing carbon easily pollute molten steel and have lower mechanical strength. In this study, ultra-low carbon MgO–C bricks containing C/MgAl2O4 composite powders used in AOD refining were explored. MgAlON as the strength phase was in situ generated in the composites (M3) containing 2 wt% C/MgAl2O4 composite powders. The samples were further compared with commercial MgO–CaO bricks (M1), which are currently used in the slag line of the AOD furnace, and the sample (M2) without the addition of C/MgAl2O4 composite powders. The hot modulus of rupture (HMOR) of M3 was the highest at 27.3 MPa, which increased 44% compared with that of M2 and increased 158% compared with that of M1. The number of thermal shock test cycles of M3 was 1.6 times that of M2. HMOR and cold crush strength (CCS) of samples after thermal shock resistance test were measured. The HMOR of M3 after 3 cycles of the thermal shock test was 2.1 times greater than that of M1. After 20 thermal shock cycles, the residual CCS ratio of M3 was highest, up to 94.6%. Improvement in the thermal shock resistance of the composites can be achieved by the addition of C/MgAl2O4 composite powders, which promote the generation of MgAlON. It was also found that the slag corrosion depth of M3 was the lowest at 64.7% of that of M2 and was 13% of that of M1. The internal micromorphologies researched by XRD and SEM and the corrosion mechanism revealed by thermodynamic calculations show that MgAlON was formed in situ after the corrosion test and endowed the composites with excellent properties.

Improved thermal shock resistance of low-carbon Al2O3–C refractories fabricated with C/MgAl2O4 composite powders

Enhanced performance of low-carbon MgO–C refractories with nano-sized ZrO2–Al2O3 composite powder

Enhanced thermal shock resistance of low‐carbon Al2O3‐C refractories via CNTs/MgAl2O4 whiskers composite reinforcement

Effect of C/MgO nanocomposite powders on the properties of low-carbon MgO–C refractories

Improved thermal shock resistance of MgO–C refractories with addition of calcium magnesium aluminate (CMA) aggregates

Enhanced performance of ultra-low carbon MgO–C bricks by the addition of special C/MgAl2O4 composite powders

Enhancing the thermal shock and corrosion resistance of low‐carbon Al2O3–C refractories: The role of h‐BN composite powder

Enhanced thermal shock resistance of low-carbon Al2O3-C refractories with direct CVD synthesis of nano carbon decorated oxides

Improved slag corrosion resistance of MgO–C refractories with calcium magnesium aluminate aggregate and silicon carbide: Corrosion behavior and thermodynamic simulation

Nanoscale toughening of low carbon Al2O3‐C refractories by means of SiCnw/Al2O3 composite reinforcement

Microstructure evolution, mechanical characteristics and erosion behavior of Cr2O3–Al2O3–MgO–ZrO2 refractories in molten reduction slag

Improved comprehensive properties of Al2O3-MgO-C refractories containing lightweight tabular alumina aggregates

Effect of stainless steel fibers on properties of MgO–C refractories

Microstructure, phase evolution, mechanical properties and slag corrosion resistance of ZrO2 reinforced Al2O3–Cr2O3 composites

Synergic Effects of Nano Carbon Sources on Thermal Shock Resistance of Al2O3-C Refractories

Enhanced thermal shock resistance of ZrO2-reinforced Al2O3–CaAl12O19 composites prepared from ferrotitanium slag: Crack propagation resistance mechanisms

Microstructure and mechanical properties of CaAl12O19 reinforced Al2O3-Cr2O3 composites

Effects of Cr2O3 Content on Microstructure and Mechanical Properties of Al2O3 Matrix Composites

Enhancement of thermal shock resistance of Al2O3–MgAl2O4 composites by controlling the content and distribution of spinel phase

Mechanical properties and microstructure evolution of MgO–Al–C slide plate refractories in presence of Al powder-modified magnesia aggregates

Designing low-carbon MgO–Al2O3–La2O3–C refractories with balanced performance for ladle furnaces