Abstract:Carbon deposition from catalytic methane decomposition has drawn increasing interest recently. Previously, we have found the carbon formation depends on the crystalline structure of the support, following the trend of Ni/CeO2 > Ni/CaO > Ni/MgO, because Ni supported on MgO is uniformly dispersed and can stabilize high-x CHx intermediates. We have also found that the addition of Pt can inhibit the carbon deposition on Co/Al2O3, because the alloying between Pt and Co results in the better dispersion of Co on the support. Furthermore, it was revealed that by judging the Ni/Mg molar ratio from 1 to 0.25 we could reduce the diameter of deposited carbon nanotubes from 20 to 12 nm, with substantially smaller production rate. All of these previous studies indicated that better dispersion of the supported metal would benefit the decreasing of carbon deposition. Here we present our recent investigation of the effect of support particle size on the carbon deposition. Three different types of 10 wt% Co/Al2O3 catalysts were prepared: Co on commercial Al2O3 (Cat 1), Co on sol-gel-processed Al2O3 (Cat 2), and sol-gel-made homogeneous Co-in-Al2O3 (Cat 3). TEM showed that the diameter of the Co3O4 particles in sol-gel Al2O3, is only around 6 nm, while it is 20-40 nm in the commercial catalyst. By using XRD and FTIR, Co was identified as crystalline Co3O4, in the as-prepared Cat 1 sample, CoAl2O4 in Cat 2, and amorphous Al2O3, in Cat 3, indicating the best dispersion in Cat 3. Methane CO2 reforming was studied on the three catalysts. Longer lifetime was measured for Cat 3 as compared to those on Cat 1 and Cat 2 (>20 h vs. 1 h). The support size effect is discussed.

Formation of Nanocarbon Structures in MgO–C Refractories Matrix: Influence of Al and Si Additives

Effect of support texture properties on Ni-Fe/γ-Al_2O_3 catalyst structure and catalytic performance for CO methanation

In-situ formation of plate-like Al4O4C and MWCNTs in Al2O3–C refractories with Al4SiC4 additives

Influence of ceramic phase content and its morphology on mechanical properties of MgO–C refractories under high temperature nitriding

Elucidating the role of Ti3AlC2 and Ti3SiC2 in oxidation mechanisms of MgO–C refractories

In Situ Catalytic Synthesis of Si3N4 Nanowhiskers Reinforced SiC Refractories and Their High-Temperature Properties

Role of nano-Al2O3 particles in improving the properties of MgO–C slide plate materials

Nanostructured Hybrid Carbon Nanotube/UltraHigh‐Temperature Ceramic Heterostructures: Microstructure Evolution and Forming Mechanism

Evolution of c-ZrN nanopowders in low-carbon MgO–C refractories and their properties

The Construction of Nanotubular Ni-Mg Phyllosilicate Solid Solution Catalyst for Boosting CO2 Catalytic Conversion: Identifying the Species Variations and Interactions

The construction of nanotubular Ni-Mg phyllosilicate solid solution catalyst for boosting CO 2 catalytic conversion: Identifying the species variations and interactions

Effect of Nanostructured Supports on Catalytic Methane Decomposition

Effects of in situ formed nanostructures on the structure and properties of C/SiOC composites

Effect of adding nickel to iron–alumina catalysts on the morphology of as-grown carbon nanotubes

Nanocatalysts Anchored on Nanofiber Support for High Syngas Production Via Methane Partial Oxidation

Catalytic Preparation of Si3N4-Bonded SiC Refractories and Their High-Temperature Properties

Improvement of Fe/MgO catalysts by calcination for the growth of single- and double-walled carbon nanotubes.

Formation of a Porous Crystalline Mg1‒ x Al2O y Overlayer on Metal Catalysts via Controlled Solid‐State Reactions for High‐temperature Stable Catalysis

Enhanced thermal shock resistance of low‐carbon Al2O3‐C refractories via CNTs/MgAl2O4 whiskers composite reinforcement

Nano-MgO: Novel Preparation and Application As Support of Ni Catalyst for CO2 Reforming of Methane

Effect of Formation of NiO-MgO Solid Solution on Activity and Stability of Ni/MgO-AN for CO2 Reforming of Methane