Abstract:The samples of commercial pure copper bars were severely plastic-deformed by different pretension and subsequently by different turns of torsion. Microstructure evolution of deformed samples was characterized using optical microscopy (OM). Longitudinal observations showed the formation of gradient microstructure with the maximum grain refinement in the surface layer of bars. Microindentation tests were conducted in the indenter load range of 100–450mN and at a loading rate of 9.6841mN/s. The hardness and Young's modulus were analyzed in the transversal section of samples using the method of Oliver and Pharr. Based on the strain gradient plasticity theory, the densities of statistically stored dislocations (SSDs) and geometrically necessary dislocations (GNDs) were calculated according to the Taylor dislocation model, respectively. Experimental results reveal that the hardness and Young's modulus decrease with the indenter load increasing. Indentation size effect on the hardness is relatively more significant than the counterpart of Young's modulus. In a certain pretension condition, the hardness values increase fast and subsequently slowly with the increase of applied torsion turns. The torsion process seems to effectively increase the material hardening due to the introduced simple shear strain. Compared to the hardness analysis, Young's modulus gently increases with the increase of torsion turns. That is due to the saturation of mechanical damage and/or crack introduced by severe deformation. In the combined tension–torsion loading, both densities of GNDs and SSDs increase with the increase of torsion turns. However, the SSDs density is higher than that of GNDs in spite of the same order magnitude. The torsional shear strain enhances the non-uniform deformation and stimulates the propagation of GNDs.

Microstructures and Mechanical Properties of Commercial Hot‐Extruded Copper Processed by Torsion Deformation

Enhancing tensile strength of Cu by introducing gradient microstructures via a simple torsion deformation

Effects of Torsional Deformation on the Mechanical Properties and Microstructures of a Commercial Pure Copper

Microstructure evolution, hardening and thermal behavior of commercially pure copper subjected to torsion deformation

Twinning Deformation and Yield Asymmetry Improvement of Magnesium Alloys by Free-End Torsion

Annealing Behavior of Gradient Structured Copper and Its Effect on Mechanical Properties

The Effects of Severe Torsion on Microstructure, Texture, and Mechanical Properties of a Pure Nickel Rod

Influence of Pre-Tension on Free-End Torsion Behavior and Mechanical Properties of an Extruded Magnesium Alloy.

Preparation and Characterization of Mg Alloy Rods with Gradient Microstructure by Torsion Deformation

Formation of Gradient Microstructure and Elimination of Tension-Compression Yield Asymmetry of the Extruded Mg-4.58Zn-2.6Gd-0.18Zr Alloy Via Free-End Torsion

Tunable Microstructures and Tensile Mechanical Properties of Oxide-Dispersion-strengthened Cu by Extrusion and Secondary Processing

Influence of Deformation Stress Triaxiality on Microstructure and Microhardness of Pure Copper Processed by Simultaneous Torsion and Tension

Experimental Study on Pure Copper Subjected to Different Severe Plastic Deformation Modes

Electron Backscatter Diffraction Analysis of the Microstructure Fineness in Pure Copper under Torsional Deformation

Microstructure Evolution of Ti-6Al-4V with Periodic Thermal Parameters During Axial Closed Die Rolling Process

Influence of Torsion Route on the Microstructure and Mechanical Properties of Extruded AZ31 Rods

Microstructural Evolution and Micro‐Compression in High‐Purity Copper Processed by High‐Pressure Torsion

Micro-structural Evolution Subjected to Combined Tension–torsion Deformation for Pure Copper

Microstructure Evolution and Mechanical Properties of Cu-9Ni-6Sn Alloy During Continuous Cold Deformation Process

Effect of Strain Reversal on Microstructure and Mechanical Properties of Ti-6Al-4V Alloy under Cyclic Torsion Deformation

Experimental Microindentation of Pure Copper Subjected to Severe Plastic Deformation by Combined Tension–torsion