Abstract:In this paper, we study the deformation behavior of nickel-based superalloys by in-situ EBSD and uniaxial tensile tests. This study mainly focuses on the microstructure evolution in the same area of the sample during deformation, including the evolution of various types of grain boundaries, geometrically necessary dislocations, grain orientations and texture, and their effect on the mechanical properties. The results show that the rotation of grains is closely related to their initial orientation during deformation. The lattice of grain is rotated to a certain extent to accommodate the more favorable orientation under low strain, leading to higher Schmid factors for the sample. Under large stresses, the grains occur deformation, multiple slip systems start simultaneously or alternately and the Schmid factors value gradually tends to stabilize at a lower level. Meanwhile, the texture orientation density of the initial Rotating cubic {001} texture, α-fiber (RD// ) texture, and γ-fiber (ND // ) gradually decrease or even disappears, while the texture orientation density of Copper {112} and Goss {011} increases during uniaxial tensile deformation for Cr20Ni80 alloy. Grain rotation may be a result of large strain due to stress triaxiality and resulting plane stress condition owing to specimen dimension, which is beneficial to improve the plastic deformability of the alloy. Interestingly, with the increase of strain, the average misorientation angle first decreases and then increases, which is associated with the dislocation density. In addition, serious torsion occurs in the grains during this process, forming a large number of substructures. These substructures result in grain refinement and the Hall-Petch effect. In fact, during the deformation process, multiple strengthening mechanisms act in coordination, leading to an increase in the strength of the alloy.

Enhancing tensile strength of Cu by introducing gradient microstructures via a simple torsion deformation

Effect of cryogenic impact deformation and subsequent annealing on microstructure and microhardness of pure copper

Tensile Deformation Behaviors of CuNi Alloy Processed by Equal Channel Angular Pressing

Enhancing tensile properties of extruded AZ31 rod by introducing gradient bimodal microstructure

Improvement of strength and ductility in a gradient structured Ni fabricated by severe torsion deformation

The Effects of Severe Torsion on Microstructure, Texture, and Mechanical Properties of a Pure Nickel Rod

Deformation Twinning Induced High Tensile Ductility of a Gradient Nanograined Cu-Based Alloy

Tensile strength and Young's modulus of Cu-Ag alloys in the evolution of microstructure into filamentary composites

Strengthening 5A02 Al alloy via gradient structures processed by severe torsional deformation

Microstructures and mechanical properties of Cu–Ti alloys with ultrahigh strength and high ductility by thermo-mechanical treatment

Remarkable transitions of yield behavior and Lüders deformation in pure Cu by changing grain sizes

Simultaneously enhancing strength and ductility of coarse grain Cu–Al alloy via a macro dual-cable structure

In-situ EBSD study of deformation behavior of nickel-based superalloys during uniaxial tensile tests

Investigations on the deformation behavior of polycrystalline Cu nanowires and some factors affecting the modulus and yield strength

Evading the Strength–ductility Trade-off Dilemma in Steel Through Gradient Hierarchical Nanotwins

Synergistic enhancement of strength and ductility in Ni via gradient dislocation structures induced by cyclic torsional deformation

Strain Strengthening Of Ag-10cu In Situ Filamentary Composite Prepared By Heavy Deformation

Influence of Deformation Twins on Mechanical Properties and Β Precipitation of Large-Cross-Section (290 Mm × 230 Mm) AZ80 Bar Fabricated by “Multi-Direction Forging + Extrusion + Cold Compression” Technique

Deformation Behavior and Microstructural Evolution of T-Shape Upsetting Test in Ultrafine-Grained Pure Copper

Extraordinary strain rate softening of metals in torsion

Incremental strain gradient plasticity model and torsion simulation of copper micro-wires