Abstract:The article deals with the results of determining the thermal conductivity coefficient from quasicrystalline coatings of the Al-Cu-Fe system in the temperature range up to 900 °C. The Al-Cu-Fe quasicrystalline alloy acquires a great interest for practical use as a material for protective coatings. The Al-Cu-Fe alloy is used to produce thermal barrier coatings in internal combustion engines, non-stick coatings on chemical synthesis equipment and in the food industry and to prevent the icing in aviation. The Al-Cu-Fe quasicrystals have low density, high hardness, high elasticity modulus, high values of corrosion resistance and wear resistance, low coefficient of friction, lowered adhesion, low thermal conductivity in combination with the coefficient of thermal expansion, which is close by its value to some metals. The water atomized Al63Cu25Fe12 powder with a dispersion of +40/-63 μm that has a content of the quasicrystalline phase of about 60 wt. % was used for spraying. The coating was sprayed to the butt of a cylindrical substrate from steel 45 (diameter – 25 mm, height – 10 mm), which before spraying was subjected to jet-abrasive treatment by corundum powder with a determining particle size of 1 mm at air pressure of spraying of 0.5 MPa. The Al-Cu-Fe coating with a thickness of more than 0.8 mm was made by high-speed air-fuel (HVAF) spraying using a burner GVO-RV12 with the following spraying mode: the pressure in the combustion chamber of the burner is 1.0 MPa; the oxidant excess coefficient a ≈ 1.2, the spraying distance is 270 mm. The samples were installed on the side surface of the drum (diameter 120 mm), which rotates at a speed of 2.0 rev/s (the speed of movement of the sputtering spot is 0.8 m/s). Spraying was done in three steps of 10 seconds each with a 30 second cooling time between them. Determination of the temperature dependence of the thermal conductivity of the coating was carried out by solving the inverse problem of thermal conductivity by one-dimensional temperature fields in samples obtained by single-sided jet heating with an industrial hot air torch (at surface temperatures up to 450 °C) and an oxygen-propane welding torch (at temperatures above 450 °C). It is shown that the values of the thermal conductivity coefficient of Al-Cu-Fe quasicrystalline coatings in the range of 20 °С...900 °С vary within λ = 1.9 – 2.31 W/(m×K).

IN-PLANE THERMAL DIFFUSIVITY OF ALUMINUM COATED STEEL SUBSTRATES

Effect of Substrate Characteristics on Interdiffusion Coefficients of Ni and Al Atoms in Β-Nial Phase of Aluminide Coatings

A Finite Difference Method for Determining Interdiffusivity of Aluminide Coating Formed on Superalloy

Study of the Mechanical Properties and Thermal Control Performance of Plasma-Sprayed Alumina Coating on Aluminum Alloy Surface

Simultaneous measurement of cross-plane thermal conductivity and interfacial thermal conductance of nano-metal films on a low thermal diffusivity substrate using TDTR

Microstructure, Properties and Mechanism of Formation of Aluminum Diffusion Coatings on Heat-Resistant Stainless Steels

Effects of Heat Treatments on Phase Structure of Electrodeposition Aluminum Coatings on Different Substrates

Thermal barrier effect from internal pore channels on thickened aluminum nanofilm

Bonding Strength and Thermal Insulation Property of Thermal Barrier Coating with Nanometer Alumina Coated Zirconia

Microstructure evolution and interdiffusion behaviors of (Ni,Pt)Al coating with and without Re-diffusion barrier on IC21 substrate at 1100°C

Investigation of interfacial thermal stabilities of Nbf/TiAl composites with and without Al2O3 coating in interface

Effect of atomic diffusion on interfacial heat transfer and tensile property of copper/aluminum composites

Preparation and Properties of Thermal Barrier Coating with Nanometer Alumina Coated Zirconia

Anisotropic thermal diffusivity measurement of thin films: From a few to hundreds of microns

Exploring thermal dynamics and porosity of cold-sprayed Ti-6Al-4V coatings on Al6061-T6 substrates: A pulsed thermography and numerical modeling approach

Effects of a nano carbide coating fabricated by EB-PVD on the interfacial stability of aluminide coated superalloy

Effect of high temperature exposure on microstructure, mechanical and tribological properties of cold sprayed NiCoCrAlTaY coatings

Influence of atomic migration mode at different temperatures on the microstructure, mechanical and cavitation erosion behaviors of Co-based alloy coating

Measurements of electron-phonon coupling factor and interfacial thermal resistance of metallic nano-films using a transient thermoreflectance technique

THERMOPHYSICAL CHARACTERISTICS OF THE HVAF COATING FROM QUASICRYSTALLINE ALLOY OF THE Al-Cu-Fe SYSTEM

Isothermal Diffusion Behavior and Surface Performance of Cu/Ni Coating on TC4 Alloy