Abstract:Compacted graphite cast iron (CGI) is a potential alternative to lightweight alloys. It is accepted that CGI can effectively reduce the automobile total weight by virtue of its high strength and its high thermal conductivity giving an opportunity to designers to design components with thinner sections. However, the successful casting process to produce this material requires detailed information for the prediction of microstructure and accurate casting process knowledge. In this paper, compacted graphite with four different cooling rates and with different Mg/S ratios ranging from 2/3 to 7/1 has been produced by using a plunger technique. The oxygen potential of all ranges has been measured by using a special oxygen potential measuring device equipped with a vibrating oxygen measurement sensor. The relationship between the oxygen potential and the graphite shape was investigated and the oxygen potential range to produce compacted graphite iron was established. It has been demonstrated that the oxygen potential measurement is a valuable method to evaluate the potential of cast iron melts to produce compacted graphite iron. La fonte à graphite compact (CGI) est une substitution possible des alliages légers. On accepte que la CGI puisse effectivement réduire le poids total de l’automobile en raison de sa grande résistance et de sa conductivité thermique élevée, donnant ainsi la chance aux concepteurs de créer des éléments à profilés plus minces. Cependant, le procédé de moulage efficace pour la production de ce matériau nécessite une information détaillée pour la prédiction de la microstructure et une connaissance précise du procédé de moulage. Dans cet article, on décrit la production de graphite compact à quatre vitesses différentes de refroidissement et à rapports différents de Mg/S variant de 2/3 à 7/1, en utilisant une technique de piston d’injection. On a mesuré le potentiel-oxygène de toute la gamme en utilisant un appareil particulier pour mesurer le potentiel-oxygène, équipé d’un capteur à vibration pour la mesure d’oxygène. On a étudié la relation entre le potentiel-oxygène et la forme de graphite et l’on a établi la gamme de potentiel-oxygène pour produire de la fonte à graphite compact. On a démontré que la mesure du potentiel-oxygène était une méthode valable pour évaluer le potentiel des bains de fonte pour produire de la fonte à graphite compact.

High-throughput Dry and Minimum Quantity Lubrication Drilling of Compacted Graphite Iron

Dry and Minimum Quantity Lubrication High-Throughput Drilling of Compacted Graphite Iron

Investigation of Drilling Machinability of Compacted Graphite Iron under Dry and Minimum Quantity Lubrication (MQL)

Machinability Improvement of Compacted Graphite Irons in Milling Process with Supercritical CO2-based MQL

Turning processes and mechanism of compacted graphite iron used for high performance engine

Experimental and FEM Study of Coated and Uncoated Tools Used for Dry Milling of Compacted Graphite Cast Iron

Surface Layer Microstructure and Mechanical Characteristics Analysis of Cast Iron During Milling Process under Supercritical CO2-MQL

Tool wear monitoring in drilling of high-strength compacted graphite cast irons

A Novel Grinding Process on Compacted Graphite Iron Using Cutting Fluid with Nano-solid Lubricant Additives

Comparative Study of Minimum Quantity Lubrication and Dry Drilling of CFRP/titanium Stacks Using TiAlN and Diamond Coated Drills

Wear Study of Cubic Boron Nitride (cBN) Cutting Tool for Machining of Compacted Graphite Iron (CGI) with Different Metalworking Fluids

Investigation Of Minimum Quantity Lubrication Effects In Drilling Cfrp/Ti6al4v Stacks

Experimental investigation on drilling machinability and hole quality of CFRP/Ti6Al4V stacks under different cooling conditions

Lubricant Coatings for Mobile Dry Drilling of Stacked Aluminium Alloys

CFRP drilling under throttle and evaporative cryogenic cooling and micro-lubrication

Prediction model optimization and experimental verification based on the material characteristic and dynamic angle on thrust force and torque in drilling GJV450

Lubricity and Rheological Properties of Highly Dispersed Graphite in Clay-Water-Based Drilling Fluids

Examination of Minimum Quantity Lubrication Performance in the Hard Turning of AISI/SAE 1060 High-Carbon Steel

OXYGEN POTENTIAL VALUES TO PRODUCE COMPACTED GRAPHITE CAST IRON

Effectiveness of lubricating coatings in dry drilling of aluminium alloys

Studying the performance of pressurized injection lubrication in drilling operations